Jump to content
SAU Community

Recommended Posts

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

Hi Guys!!!

I have 1994 S1 R33 GTST complete for wrecking, car is still complete and running due to i cant sell the complete car and i really needed the money so im going to have to wrecked.

Car had just over 100 000 klms on clock been sitting for a while now. Car is gun metal grey in colour. Car is complied.

Engine complete r33 series 1 (standard) with 100 000 klms on clock $2000 harness ecu turbo .

Complete 5 speed conversion gear box and the rest $2000

Front windscreen $100

Rear windscreen $200

Side quater window $50 each

Standard fmi with pipe $50

Cat back exhaust $200

S1 AFM $115

Quick shift kid $100

climate control $50

charcoal cannister $30 (smaller size type)

ac Fan $80

hub/fan $150

Radiator $150

rad. shroud $50

Condensor s1 $100

gaurds $100

s1 front bar $200

Front bar enforcment support $150

bonnet $250

side skirts $150 pair

s1 cluster $230 with 100 000klms...

s2 front grill $100

rear tailghts $250 complete

rear bar $100

rear garnish $70

Rear pod $80

Doors $50 each

Window motor $140

Window maganisium $50

Front Lh, RH glass $60 each

Door mirror $70 each

boot lid $100

s2 boot spoiler $150

drivers window switch $120

Passenger side $60

complete interior $200 minus rear seat......happy to separate seats trims etc.....

Adjustable coilovers $900 for the set fronts and rears

Rear diff $400

rear / front lower control arms $100 each

R34 Gt rim a set with good rubber $300

complete 5 stud conversion $800..happy to separate suspension also..........

happy to separate the shell eg Radiator support, rears quaters etc.

PLEASE ASK IF I LEFT ANYTHING OUT.

there heap of parts left.

post-40081-1222178372_thumb.jpg

post-40081-1222178395_thumb.jpg

post-40081-1222178416_thumb.jpg

post-40081-1222178442_thumb.jpg

post-40081-1222178461_thumb.jpg

post-40081-1222178482_thumb.jpg

post-40081-1222178597_thumb.jpg

post-40081-1222178626_thumb.jpg

post-40081-1222178652_thumb.jpg

post-40081-1222178674_thumb.jpg

dinzlr/khmer whatever... you were banned before.

You've been banned again. Stop signing up fool.

Anyone doing dealings, or thinking about it - should cease with this person

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
×
×
  • Create New...