Jump to content
SAU Community

Recommended Posts

Yesterday went to Turbotune in Adelaide to fix a spluttering problem my car has had for a while. Thought it could be either a fuel pump problem or a coilpack. After an hour and some tests, ended up being a faulty coil pack. So happy to get that fixed coz it was driving me crazy. Then we dynoed it and I was shocked to see 201.2rwkw. Only mods are dump/front pipe, hks cat back, fmic, no boost controller but there was a boost increase to around 11.5psi. I was wondering if anybody made similar sort of power with or without boost controller. Will put picture of dyno when I get a chance to scan.

Link to comment
https://www.sau.com.au/forums/topic/235496-dynoed-my-r33/
Share on other sites

  • Replies 54
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

to me that dyno is reading a wee bit too high

i had my car dynoed at Willall Racing and they use a mainline dyno

with a front mount, boost increase to 9psi, full zorst, splitfire coilpacks, pod....my car made 188.7 rwkw on a reasonably warm day

so from the mods that you are saying you have i would expect the same sort of power that my car has pulled out

plus no boost controller and ur hitting 11.5psi....umm have you had that reading out off a boost gague or from the stock gauge.

Edited by Krishy
Link to comment
https://www.sau.com.au/forums/topic/235496-dynoed-my-r33/#findComment-4123368
Share on other sites

damo had 2 dyno results from 2 different places.....

autosalon dyno if i remember correctly he made 161 something rwkw

and at southern hi tech dyno he made 184.2rwkw

that alone tells you that every dyno is different

Edited by Krishy
Link to comment
https://www.sau.com.au/forums/topic/235496-dynoed-my-r33/#findComment-4123473
Share on other sites

Only mods are dump/front pipe, hks cat back, fmic, no boost controller but there was a boost increase to around 11.5psi. I was wondering if anybody made similar sort of power with or without boost controller. Will put picture of dyno when I get a chance to scan.

You WOULD have about 200rwkw if there was an aftermarket computer or your ecu has been remapped........

Link to comment
https://www.sau.com.au/forums/topic/235496-dynoed-my-r33/#findComment-4123484
Share on other sites

my 33 made 192kw with just a pod and turbo back three inch exhaust. i fitted the FMIC and it automatically pushed the boost up. final result is 205.4kw on 10psi :blink: ... i'm stoked:) oh and im running stock ECU and no boost controller

Edited by IZZMO 33
Link to comment
https://www.sau.com.au/forums/topic/235496-dynoed-my-r33/#findComment-4123529
Share on other sites

Southern Hi Tech: 182.4rwkw

Autosalon: 165rwkw

I got the lighter wheels back on and have a dyno day at graham west next month. im very interested to see what it pulls now, although i may have a few goodies on by then so the comparison wont be that accurate.

At autosalon in 4th it was hitting speed cut on the ctock ecu but hadn't maxed the revs yet, but at southern hi teech it reached max revs, so i guess each dyno is calibrated differently.

Edited by Damo_R34
Link to comment
https://www.sau.com.au/forums/topic/235496-dynoed-my-r33/#findComment-4123552
Share on other sites

my 33 made 192kw with just a pod and turbo back three inch exhaust. i fitted the FMIC and it automatically pushed the boost up. final result is 205.4kw on 10psi :blink: ... i'm stoked:) oh and im running stock ECU and no boost controller

same goes here, i achieved quite a boost increase after installing FMIC. Around 12psi. no aftermarket boost controller, and what appears to be the standard ECU. Same other mods that IZZMO mentioned - pod, turbo back exhaust.

She's running pretty nice.

Next thing i'll be adding is better coil packs - my oem ones are pretty fried.

Link to comment
https://www.sau.com.au/forums/topic/235496-dynoed-my-r33/#findComment-4123577
Share on other sites

Mainlines do read lower due to their more accurate correction factors but this is widely know, so you can compare DD figures to DD amd mainline to mainline but can't really compare them against eaach other.

I fitted the exhaust and cooler to this car, there was also some cat "modifications" so the boost increase is due to the increase in the exhaust flow.

The boost reading is off the MAP sensor on the exhaust.

I would say that the figure is pretty accutre due to how i only just pulled away in my lighter 180 which was running about 205kw(14.5psi) at the time when we had a run on the freeway on the way to Mallala (kept it under 110 of course).

As cubes and Jeff said prehaps it's just a freek.

Edited by D_Stirls
Link to comment
https://www.sau.com.au/forums/topic/235496-dynoed-my-r33/#findComment-4123645
Share on other sites

Where there is a boost jump it should only jump to around 9 or 10psi. Most 33's do that with those mods, but I think there are some that just might do crazy things and jump to 11 or 12 psi like mine and I dont know why, maybe just lucky. Plus turbo tune had just finished having they're dyno serviced on monday, so dont think the dyno is a problem.

Link to comment
https://www.sau.com.au/forums/topic/235496-dynoed-my-r33/#findComment-4123646
Share on other sites

damo had 2 dyno results from 2 different places.....

autosalon dyno if i remember correctly he made 161 something rwkw

and at southern hi tech dyno he made 184.2rwkw

that alone tells you that every dyno is different

auto salon was dead on actually. i had just got my car dyno tuned at boost worx a week prior and it made 2kws more than it had been tuned for.

anywho.. i dont find it hard to believe 200. i mean 11.5 is lot of boost for a rb25.

Link to comment
https://www.sau.com.au/forums/topic/235496-dynoed-my-r33/#findComment-4123650
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...