Jump to content
SAU Community

Recommended Posts

I am planning to install a AFC neo on my R33 Gts t Series 1, coz it is running really rich.

now here is my query, will tuning the car with an AFC affect the timing? the way i understand how it works is, it restricts the amount of fuel but it does it in such away that the ECU still cranks the timing right up for a rich mixture. wont this stuff my car eventually??

it cant be good having the timing and the A/F mix all wrong can it?

Link to comment
https://www.sau.com.au/forums/topic/235520-afc-neo/
Share on other sites

The AFC's change the Airflow meter signal to the ECU and can not change the ignition timing. It tricks the computer into thinking there is less air than there is in the system so that it does not inject as much fuel, this should only be modified with a wide band o2 sensor hooked up or you can make it run too lean and kill the engine.

Link to comment
https://www.sau.com.au/forums/topic/235520-afc-neo/#findComment-4124009
Share on other sites

it will be getting installed and tuned at a reputable workshop, so i would assume they would do it with a wideband o2 sensor. last time they had a graph from the dyno with the results of the AF mixture, they will be doing that again after it is tuned so i will be able to see.

but will the timing be an issue if it is tuned properly?

the timing will still be out even if it is tuned properly. right??? :P

i just dont wanna kill my car is all. i want it perfect.

Link to comment
https://www.sau.com.au/forums/topic/235520-afc-neo/#findComment-4124044
Share on other sites

if you lower the correction value to take fuel out, the ecu thinks there is less airflow and doesn't inject as much fuel, which also makes the ecu not add as much ignition timing. if you raise the correction value to add more fuel, the ecu thinks your flowing more air so it adds more fuel, which also inadvertantly adds more timing.

nothing to worry about though. not unless your at -50% correction on the fuel map at full throttle, which wont be the case. lots of people run AFC's and don't have a problem. keep in mind the AFC is only really good for a mild modded setup.

Link to comment
https://www.sau.com.au/forums/topic/235520-afc-neo/#findComment-4124760
Share on other sites

The AFC neo, safc and any piggyback without ignition timing adjustment is purely a bandaid for the rich n that rb25's suffer from...and for obvious reasons its best to upgrade to pfc for the best results but if your budget doesn't stretch then yea it will help to a certain degree...pardon the pun.

Link to comment
https://www.sau.com.au/forums/topic/235520-afc-neo/#findComment-4125041
Share on other sites

The AFC neo, safc and any piggyback without ignition timing adjustment is purely a bandaid for the rich n that rb25's suffer from...and for obvious reasons its best to upgrade to pfc for the best results but if your budget doesn't stretch then yea it will help to a certain degree...pardon the pun.

The tuner should adjust the timing to eliminate any knock. For best performance also get an Apexi SITC to get the best timing across the rev range.

Link to comment
https://www.sau.com.au/forums/topic/235520-afc-neo/#findComment-4125937
Share on other sites

I only have a pod filter and 3inch exhaust on the car, im just sick of the richness robbing my power.

It is just a quick fix really until i can afford to get a HKS GTRS turbo kit, Greddy FMIC and a PFC, maybe some splitfires and nismo injectors if the budget will allow, which will be a while away so i want something to help in the meantime.

I just dont wanna wreck my engine while im waiting to save up enough cash the upgrades.

Link to comment
https://www.sau.com.au/forums/topic/235520-afc-neo/#findComment-4128667
Share on other sites

What would be a mild modded setup ? I am having the same problem choosing either the SAFC or the PFC

exhaust, FMIC, maybe a bit more boost. if you have plans for future mods you will be better going for a PFC. also even on mild mods a PFC will still give a better tune than a SAFC.

Link to comment
https://www.sau.com.au/forums/topic/235520-afc-neo/#findComment-4128929
Share on other sites

I'd go to a PFC with exhaust and FMIC.

I'd only use a SAFC if I only had one of the two mods, and I had no intention of doing anything more to the powertrain than that.

A SAFC is something you do if you plan on keeping the car practically stock but you don't like your rear bar covered in carbon. Like ryan said, its just a band-aid solution.

Link to comment
https://www.sau.com.au/forums/topic/235520-afc-neo/#findComment-4129018
Share on other sites

ok, so my car will be fine for a year then? i wanna save up enough money to get it all done at once to save on tuning costs.

i havent had the Skyline that long and it seems to be in the workshop all the time, i would like to be able to drive it for a while with no problems, so i can save up money for upgrades.

im hoping the AFC will do the trick and keep me happy for a while. :)

Thanks for the replies guys, ive decided im gonna put it in next week, damn workshop is always booked up. :P

Edited by GreyGTST
Link to comment
https://www.sau.com.au/forums/topic/235520-afc-neo/#findComment-4129147
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I had 3 counts over the last couple of weeks once where i got stranded at a jdm paint yard booking in some work. 2nd time was moving the car into the drive way for the inspection and the 3rd was during the inspection for the co2 leak test. Fix: 1st, car off for a hour and half disconnected battery 10mins 4th try car started 2nd, 5th try started 3rd, countless time starting disconnected battery dude was under the hood listening to the starting sequence fuel pump ect.   
    • This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
×
×
  • Create New...