Jump to content
SAU Community

Recommended Posts

Hi;

New to the GTR.

Have an 1992 GTR RB26 DETT and temp gauge in the instrument cluster in not registering anything. From what I've read, there are two coolant temp sensors? - one for ECU and one for temp gauge.

Checked ECU temp sensor and resistances are in normal range (according to manual) . Checked the smaller sensor next to it on the coolant housing (single wire sensor) but can't find any specs on normal resistance ranges. Also removed the instrument cluster in off chance there might have been a loose plug or obvious wire disconnect - no such luck.

Not sure how to troubleshoot this one. Are there two sensors - one for ECU , one for temp gauge. Found info on diagnostics in the manual for the ECU coolant temp sensor but how do to troubleshoot temp gauge sensor if it is separate? Curiously, heater doe snot seem to throw much heat either.

Link to comment
https://www.sau.com.au/forums/topic/235636-temp-gauge-not-working/
Share on other sites

I think if you ground the wire the goes to the sensor, the gauge should go full-scale. This will confirm the gauge is working.

The problem with the heater is totally separate. Have you checked that a thermostat is installed? Is the top hose of the radiator hot when the engine is up to temperature (been working for more than about 10 minutes)?

Thanks, I'll try grounding the sensor wire.

Yeah - heat in cabin was not suspected to be connected to the gauge but might be a symptom of what led us to the gage. Absolutely have heat at top of radiator - kinda started the whole deal. Short version of a long story -> Just got the car this spring and it has taken until now to get it road ready. Finally about to take it to have it tuned when we stumbled upon the temp gage not working (thought car might be running hot) and so here we are trying to get temp gauge functional to be able to get back to original plan<- I'll need to check for the thermostat.

Appreciate the help. I'll advise if gauge works.

I think if you ground the wire the goes to the sensor, the gauge should go full-scale. This will confirm the gauge is working.

The problem with the heater is totally separate. Have you checked that a thermostat is installed? Is the top hose of the radiator hot when the engine is up to temperature (been working for more than about 10 minutes)?

Gauge works - anybody know the part # for the temp gauge sensor? 92 GTR RB26DETT

Thanks, I'll try grounding the sensor wire.

Yeah - heat in cabin was not suspected to be connected to the gauge but might be a symptom of what led us to the gage. Absolutely have heat at top of radiator - kinda started the whole deal. Short version of a long story -> Just got the car this spring and it has taken until now to get it road ready. Finally about to take it to have it tuned when we stumbled upon the temp gage not working (thought car might be running hot) and so here we are trying to get temp gauge functional to be able to get back to original plan<- I'll need to check for the thermostat.

Appreciate the help. I'll advise if gauge works.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...