Jump to content
SAU Community

Recommended Posts

Hey guys,

Over the last week my car has developed a pretty bad stalling problem. It cuts out while slowing down for traffic lights or when pulling into the driveway. Then last night when driving I could smell something burning, about 30 seconds later the car cut out while still going 60km/h :P

Other info which might be relevant...

- my exhaust manifold was replaced about 2 weeks ago

- the problem is worse when the aircon is on

Any help would be appreciated :thanks: thanks

Link to comment
https://www.sau.com.au/forums/topic/235964-bad-stalling-problem/
Share on other sites

reset stock ecu

if still persists check battery voltage

if still persists go see an auto elec/mechanic

Thanks, now that you mention it my battery is getting a bit old. The car needed a jump start after leaving the radio on for only 5-10 minutes. Do you think this could be the cause? I've mentioned this to a few people but they seem to think it's unrelated.

do you have an aftermarket bov?

Nope, car is pretty close to stock.

Edited by rick444
Thanks, now that you mention it my battery is getting a bit old. The car needed a jump start after leaving the radio on for only 5-10 minutes. Do you think this could be the cause? I've mentioned this to a few people but they seem to think it's unrelated.

Nope, car is pretty close to stock.

Check all your electrical plugs in your engine bay, first place i'll be looking is the AFM. is your car boosting ok? maybe borrow a friends AFM and i suggest you replace your battery, you dont want to be stuck with a flat!

I just checked out all the plugs in the engine bay and everything seems fine.

However when I let the off the throttle and the revs drop, sometimes I hear a faint crackling noise coming from the back of the engine bay, it almost sounds like electricity arcing, but I can't be sure. It only lasts a second and I can't find the source of it.

Mine was doing this last week. I changed the o2 sensor (could see it rich at idle on dyno) and its fixed the problem. I didnt think it was the problem but turned out to be!!

+1

might be worth a shot if you cant find the problem. do a search on the forums and you will find loads of threads on the o2 sensor.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...