Jump to content
SAU Community

Recommended Posts

Item: R32 5 point Cusco bolt on half cage

Condition: Very Good

Price: $550 ono

To Fit: (What car) R32 Gtst or Gtr

Location: Adelaide

Comments: Comes with all bolts, nuts, plates etc.... ready to bolt on.

post-18416-1221394153_thumb.jpg post-18416-1221394177_thumb.jpg

Edited by Richo
Link to comment
https://www.sau.com.au/forums/topic/236060-r32-cusco-roll-cage/
Share on other sites

  • 2 weeks later...
wont fit dude
^^^ as he said mate, it wont fit! back legs sit on the wheel archs.

hmmm thats weard i put this tomie 2 door cage in my 4 door

unless my mate 2 door had a 4 door cage in it

it was easy to install as well with the 4 doors an all lol

07102008178.jpg

07102008179.jpg

28092008172.jpg

yeah i dont see why it wouldnt fit, the chassis is basically the same as a 2 door with just another door added in to get into the back

maybe get this bloke to get some measurements to see if it will mount like the one above GTS4WD

it will fit if u make it, but it sits too far back!

if u think about it, if the car rolls, all the weight/force will go straight to the drivers/passengers head while ur back seats will be protected!

i would think the 4 door and 2 door have the same floor pan

it bolted to the same place than the 2 doorwe had them next to each other

strate out of 2 door in to the 4 door same holls same place

and it looked the same

but i cant rember where the top bar went over the head rest in the 2 door

but my seats are just a bit forwared than normal in the pics

also the rear door handels just hit the cage when i close them

Edited by dreadr31

yeah from memory both 2 door and 4 door cages will fit each other, if you look at the size of the front doors from 2 door and 4 door, the 2 door is longer,

so if the 2 door cage sits at the pillar it will sit a bit behind the pillar in a 4 door, but will still connect to the wheel arch and then the distance to the dash will be the same as it sits further back,

so it should fit 2door and 4door

JV

  • 2 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Oh, also, forgot to add these photos I believe.
    • Thought i'd update on this. I was able to get in contact with Craig Lieberman and later on Darryl Alison (owner of Kaizo Industries). Darryl was able to help me verify that my car was in fact one of theirs and is helping me find more info on mine !
    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
×
×
  • Create New...