Jump to content
SAU Community

Recommended Posts

Item: R32 5 point Cusco bolt on half cage

Condition: Very Good

Price: $550 ono

To Fit: (What car) R32 Gtst or Gtr

Location: Adelaide

Comments: Comes with all bolts, nuts, plates etc.... ready to bolt on.

post-18416-1221394153_thumb.jpg post-18416-1221394177_thumb.jpg

Edited by Richo
Link to comment
https://www.sau.com.au/forums/topic/236060-r32-cusco-roll-cage/
Share on other sites

  • 2 weeks later...
wont fit dude
^^^ as he said mate, it wont fit! back legs sit on the wheel archs.

hmmm thats weard i put this tomie 2 door cage in my 4 door

unless my mate 2 door had a 4 door cage in it

it was easy to install as well with the 4 doors an all lol

07102008178.jpg

07102008179.jpg

28092008172.jpg

yeah i dont see why it wouldnt fit, the chassis is basically the same as a 2 door with just another door added in to get into the back

maybe get this bloke to get some measurements to see if it will mount like the one above GTS4WD

it will fit if u make it, but it sits too far back!

if u think about it, if the car rolls, all the weight/force will go straight to the drivers/passengers head while ur back seats will be protected!

i would think the 4 door and 2 door have the same floor pan

it bolted to the same place than the 2 doorwe had them next to each other

strate out of 2 door in to the 4 door same holls same place

and it looked the same

but i cant rember where the top bar went over the head rest in the 2 door

but my seats are just a bit forwared than normal in the pics

also the rear door handels just hit the cage when i close them

Edited by dreadr31

yeah from memory both 2 door and 4 door cages will fit each other, if you look at the size of the front doors from 2 door and 4 door, the 2 door is longer,

so if the 2 door cage sits at the pillar it will sit a bit behind the pillar in a 4 door, but will still connect to the wheel arch and then the distance to the dash will be the same as it sits further back,

so it should fit 2door and 4door

JV

  • 2 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
×
×
  • Create New...