Jump to content
SAU Community

Recommended Posts

Hey guys have a s15 centre and halfshafts that im going to put into my r32 gtst housing if its not too hard as mines screwed. I have s13 driveshafts that i can bolt onto the halfshafts. All i need to know is will the s13 driveshafts fit into my r32 rear hubs? And would they be the right length. I hope they will as s13 and r32 rear setup is similar. Any help would be great...

Thanks guys :down:

Link to comment
https://www.sau.com.au/forums/topic/236331-s13-driveshafts-into-r32-hubs/
Share on other sites

Yeah i have heard that they are weaker but the still take over 300rwkw so i should be fine. If my half shafts fit into the diff then ill keep them for sure, just didnt think they would fit. Guess theres only one way to find out...

Has anyone else done this before?

the s15 center has more splines and a larger diameter from memory. The r32 output shafts won't fit the center.

You will need to use the s15 output shaft and the s13 drive shaft.

The car i'm buying actually has this done :P and will get my r32 diff with nismo center and r32 drive shafts installed in it too.

You can pretty much swap anything around between s13 and r32 at the back end with no problems. Even the arms, sway bars and struts are interchangable

they are, but on the 32 shafts theres also a section thats a smaller diameter than the rest. Thats the point it'll fail at if the shaft is going to fail.

Alot of people seem to kill the inner CV's before the shaft though which implies thats the weak link.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nah, don't bother doing any actual measurements on the car. Just go ask the inter-f**king-net.
    • I currently have 18 x 9 +30 on the front with 18 x 10.5 +38 on the rear. Absolutely regretted it. Ended up putting 15 mm spacers on front and 25 mm spacers on the rear. Not to mention the rears were like a mm from hitting the coilovers. Definitely would go more aggressive then what you were originally planning. Keep in mind my guards are rolled and cars fair low so you might possibly need to roll guards depending how aggressive you go and how low the car is. Im not an expert but the 18 x 8.5 +25 18x9.5 +30 Sounds like it would sit much better.
    • Hey guys, sorry i have been researching for a few months and absolutely cannot wrap my head around this. I am about to order some rims to fit my R34 Gtt with coilovers My original plan was to order Rota grid R in 18x8.5 +30 235 40 R18 Fronts 18x9.5 +35 255 35 r18 rears But then the thought in my head said this isnt aggressive enough. I want the most concave spokes i can get without too much of poke and scrubbing   So my thoughts now is  18x8.5 +25 18x9.5 +30   My question is will this be the most aggressive i could get it without any guard rolling and does the type of rim style affect the offset / size.   Thanks everyone.
    • Lower parts are there. On passenger seat, bright yellow bit is the release mount. On drivers, bright yellow bit is the lower buckle for the other side. My bet is lowers are tucked out of the way as much as possible for visuals.
    • I'm guessing its a 4 point harness, 3 of the 4 belts are visible. I'm guessing the hidden belt is tucked down between the seat and door. 
×
×
  • Create New...