Jump to content
SAU Community

Recommended Posts

have had a towbar and wire plug fitted.was then told that with this model of car the indicators draw too much current when you have a trailer or caravan connected,so would have to replace caravan indicator bulbs with led.have done that and at least the indicators work now,but very faint. ha s anybody overcome this problem? any help/comments most appreciated.

Link to comment
https://www.sau.com.au/forums/topic/236806-v-series-towbar-wiring/
Share on other sites

ok - if you were QLD based I was going to tell you to come see me.

I would find a autoelec used to working on BMW/benz as those cars sort of follow your rules.

the idea on what I have said is to switch current off the battery supply rather than the acutal lights. you use the lights to trip the relays.

You need something called a power converter - attached is the Infiniti TSB that talks about it (G35 = USDM version of our V35 Skylines). Basically it is a box that contains the relays which Chris refers to.

Not sure where you can get these in NZ - maybe Supercheap/Repco?

As Chris notes somebody who works with Euro cars can probably help.

Where did you get your towbar fitted and what did it cost? Been meaning to get one fitted to my 250GT for a while now...

If you get this sorted can you post up here again - useful info for the Auckland dwellers... :(

ITB04_020e.pdf

that in reality gives MORE than enough info to make one.

go to jaycar and get:

5 transistors (BC337 will do)

5 10k resistors

5 diodes (1N4004 will do)

5 SPST 12v relays (12v coils)

and build 5 separate circuits using the transistor and resistor to drive the relay . the diode is there for spike protection from the relay coil

see here for the concept:

http://www.jaycar.com.au/images_uploaded/relaydrv.pdf

you need the first one

diopro.gif

background here

http://www.kpsec.freeuk.com/trancirc.htm

from there Download the data sheet on the BC337

http://www.datasheetcatalog.org/datasheet/...ips/BC337_3.pdf

pin it out and away you go.

the OE lights fire the transistor (draw on this is WELL below the spec in the nissan sheet posted above.) that in turn fires the relay and sends 12v to the auxilary lights (IE trailer.)

theres my $1 worth on this topic :(

holy crap,thats too much information,im a chippy not a diode soldering type person.!! the tow bar was manufactured and fitted by ackerbilt in penrose,nice tidy job but i obviously cant recommend their wiring!!.it cost $490.00 all up.will post again when this is sorted.thanks people for your help.

Cheers for that Chris, wish I had time to whip up something like that...

I'm guessing you should be able to get something like that from an auto sparky who knows what they are doing. I know a good one in Pt Chev - Ron Wood auto electrical. Not sure if he has these modules, but he knows what he is doing so might be able to help.

Will keep my eye open for one of these modules - shouldn't be too hard to come by these days.

Ant,

thing is with these cars I have to make things like that. I have found if you upset one of these cars it will stay mad at you for a LONG time. the later cars ('04.5+ ) are straight CAN and really do not like being fiddled with.

background is electronics eng. mixed with autoelectrics.

find someone who has a electronics background they can knock that up in no time. (I'm in the midst of doing one now for a car.)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
×
×
  • Create New...