Jump to content
SAU Community

Recommended Posts

Well this is starting to annoy the shit out of me.. Long story short.. I got some New Tyres Fitted to my 20" rims on R34 GT-T. previously had ghey WANLI's with puncture.. no probs. got New Kuhmo's fitted to Rims, Same size 225/35/R20.

Came home Put wheels on. went for a very short drive and noticed that the Upper control arm is scrubbing badly on top flat part of the tyre, and quite audible too.. any ideas what this is? I tried to contact the place where I purchased them but they are closed.. sadly..

:mellow:

fairly obvious isnt it, tyre is to big for vehicle, just because it is same size as specified doesnt mean each manufacturers tyres are identical size. think of it like shoes. size 9 in different brand can be different size.

Well this is starting to annoy the shit out of me.. Long story short.. I got some New Tyres Fitted to my 20" rims on R34 GT-T. previously had ghey WANLI's with puncture.. no probs. got New Kuhmo's fitted to Rims, Same size 225/35/R20.

Came home Put wheels on. went for a very short drive and noticed that the Upper control arm is scrubbing badly on top flat part of the tyre, and quite audible too.. any ideas what this is? I tried to contact the place where I purchased them but they are closed.. sadly..

;)

What width and offset?

Even with the slight differences between the patterns, there is no way a 225/35/20 should be rubbing?

Do the wheels sit well inside the guard much?

No spacers on the hub, the wheel sits roughly half inch inside the guard. im gonna get some 10mm spacers, and see if that can correct it.

  • 2 weeks later...
No spacers on the hub, the wheel sits roughly half inch inside the guard. im gonna get some 10mm spacers, and see if that can correct it.

How did you go with the rims? Please tell me you weren't meaning floating spacers, if you have to use any you should use a bolt on item. I had to use them on my brothers Stagea when 20s wer fitted (it had the same issue as you have).

I ended up doing a Jesse James and getting the old grinder out. Nothing too serious, just a few mill off the upper control side arms. looks good too. gave me just over a Centimeter clearance.

I ended up doing a Jesse James and getting the old grinder out. Nothing too serious, just a few mill off the upper control side arms. looks good too. gave me just over a Centimeter clearance.

:wave:

Ok...

either way if you get a 225/35/20 it should be 225mm wide, 35% of that tall and for a 20 inch rim. I can tell there may be ever so slight differences but it shouldnt be much. Maybe your 20s were second hand and the tires already worn down with the last set?

Either way i will chew my tire up before grinding away my control arms

The correct answer to this entire thread is your tyre profile is completely incorrect! Factory OD (overall diameter) is approx 634mm (225/45/17). with 225/35/20 you have increased your OD to 665mm which is close to 5% or an extra 30mm which would have most likely thrown ur speedo out as well. In QLD, the max you can increase your OD by is 15mm.

So I would advise you to go back to whichever tyre shop you got your wheels from and get them to put the correct profile tyres on. Without knowing what width your wheels are, I'd recommend 235/30/20 to bring it close to factory OD.

different tyres have bigger tread then others. with kumos mine rubs on the coilovers at the back. if you get 225/30/20 they will be exactly the same size as a 33 stocky so you should be fine. i got sunny tyres once n the 20 was smaller then my stockies standing next to it but i still got defeted because " my speedo was out". load of bullshit. it changed it by .5 km/h. moral of the story is dont get kumos...they will be balled before you finish your tank of petrol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...