Jump to content
SAU Community

Recommended Posts

  • Replies 43
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

i just went and checked... and i found that resistor....but it is already pluged in... so it can't be that.... the plug i am trying to find a home for is the same plug as the one the one that plugs into the resistor though...

bugger....

i just went and checked... and i found that resistor....but it is already pluged in... so it can't be that.... the plug i am trying to find a home for is the same plug as the one the one that plugs into the resistor though...

bugger....

and the colour of the wires that go to it are pale green and a blue one

have you check to make sure u have a positve feed to the coils, an earth and pulse feed from igniter.

i have done yes, i have tested for earth on the coilpack plug (all is good) and the test light flashes when i connect it to the poitive side of the coilpack plug (when i crank the motor over)

in the manual i have, it says to connect the multimeter to earth and the other lead to the middle wire on the coilpack plug.... but it does'nt tell me what the multimeter should read?...

should be. under crank just make sure you don't have a voltage drop on the earth side. get ya multimeter and select voltage and connect one lead to the earth on the battery and the other to the engine. you should not see anything greater then .5volt...... also check the positive side of the coil under crank to make sure you don't have a voltage drop. under crank you'll expect to see the voltage drop to 10volts at the battery and no less at the coils.

i don't think it's a computer problem as he has an injector pulse and pulse to the coils. the cas sends a pulse to the computer and the computer outputs to the coils and injectors.

true but its worth a try wouldnt ya think. just plug and play

and lets not 4get he went through how many batteries.....

Edited by skylinekid

ok all plugs accounted for

cranks over fine now, good oil pressure.

still no spark though, checked earth wires etc., i have a multimeter handy if some one can tell me how to test the colipack plugs and ignightor properly and what readings i should get etc.

not alot of gtr's down here still, so i cant really swap ecu's etc.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I know why it happened and I’m embarrassed to say but I was testing the polarity of one of the led bulb to see which side was positive with a 12v battery and that’s when it decided to fry hoping I didn’t damage anything else
    • I came here to note that is a zener diode too base on the info there. Based on that, I'd also be suspicious that replacing it, and it's likely to do the same. A lot of use cases will see it used as either voltage protection, or to create a cheap but relatively stable fixed voltage supply. That would mean it has seen more voltage than it should, and has gone into voltage melt down. If there is something else in the circuit dumping out higher than it should voltages, that needs to be found too. It's quite likely they're trying to use the Zener to limit the voltage that is hitting through to the transistor beside it, so what ever goes to the zener is likely a signal, and they're using the transistor in that circuit to amplify it. Especially as it seems they've also got a capacitor across the zener. Looks like there is meant to be something "noisy" to that zener, and what ever it was, had a melt down. Looking at that picture, it also looks like there's some solder joints that really need redoing, and it might be worth having the whole board properly inspected.  Unfortunately, without being able to stick a multimeter on it, and start tracing it all out, I'm pretty much at a loss now to help. I don't even believe I have a climate control board from an R33 around here to pull apart and see if any of the circuit appears similar to give some ideas.
    • Nah - but you won't find anything on dismantling the seats in any such thing anyway.
    • Could be. Could also be that they sit around broken more. To be fair, you almost never see one driving around. I see more R chassis GTRs than the Renault ones.
    • Yeah. Nah. This is why I said My bold for my double emphasis. We're not talking about cars tuned to the edge of det here. We're talking about normal cars. Flame propagation speed and the amount of energy required to ignite the fuel are not significant factors when running at 1500-4000 rpm, and medium to light loads, like nearly every car on the road (except twin cab utes which are driven at 6k and 100% load all the time). There is no shortage of ignition energy available in any petrol engine. If there was, we'd all be in deep shit. The calorific value, on a volume basis, is significantly different, between 98 and 91, and that turns up immediately in consumption numbers. You can see the signal easily if you control for the other variables well enough, and/or collect enough stats. As to not seeing any benefit - we had a couple of EF and EL Falcons in the company fleet back in the late 90s and early 2000s. The EEC IV ECU in those things was particularly good at adding in timing as soon as knock headroom improved, which typically came from putting in some 95 or 98. The responsiveness and power improved noticeably, and the fuel consumption dropped considerably, just from going to 95. Less delta from there to 98 - almost not noticeable, compared to the big differences seen between 91 and 95. Way back in the day, when supermarkets first started selling fuel from their own stations, I did thousands of km in FNQ in a small Toyota. I can't remember if it was a Starlet or an early Yaris. Anyway - the supermarket servos were bringing in cheap fuel from Indonesia, and the other servos were still using locally refined gear. The fuel consumption was typically at least 5%, often as much as 8% worse on the Indo shit, presumably because they had a lot more oxygenated component in the brew, and were probably barely meeting the octane spec. Around the same time or maybe a bit later (like 25 years ago), I could tell the difference between Shell 98 and BP 98, and typically preferred to only use Shell then because the Skyline ran so much better on it. Years later I found the realtionship between them had swapped, as a consequence of yet more refinery closures. So I've only used BP 98 since. Although, I must say that I could not fault the odd tank of United 98 that I've run. It's probably the same stuff. It is also very important to remember that these findings are often dependent on region. With most of the refineries in Oz now dead, there's less variability in local stuff, and he majority of our fuels are not even refined here any more anyway. It probably depends more on which SE Asian refinery is currently cheapest to operate.
×
×
  • Create New...