Jump to content
SAU Community

No Spark Problem, Help Me Locate The Problem

ECR 033

By ECR 033,
in Engines & Forced Induction

 Share

Recommended Posts

  • Replies 43
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

116.hks Community Regular

116.hks

Posted
Posted

from memory the relay for the coils is mounted in the passenger kick panel near the computer. power is supplied from a block fuse, i believe it's rated at 25amps, in the fuse box in the engine bay. check if you are getting a constant positive on the thick white wire, orange should be ignition feed and it should have a constant earth as well. relay pin outs should be 1 and 2 are the coil of the relay and, 3 and 5 are the contacts. if you bridge the contacts of the relay with a bit of wire then you should have power at the coils. see if the car starts.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      R32 Gtst - Track Car

      By Duncan · Posted

      Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • Dose Pipe Sutututu
      R32 Gtst - Track Car

      By Dose Pipe Sutututu · Posted

      https://www.facebook.com/share/p/18rmVb1SKB/ 
    • GTSBoy
      Leak from Tokico BM50 Brake Master Cylinder

      By GTSBoy · Posted

      The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • No Crust Racing
      R32 Gtst - Track Car

      By No Crust Racing · Posted

      Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • MBS206
      R32 Gtst - Track Car

      By MBS206 · Posted

      I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...