Jump to content
SAU Community

Recommended Posts

Hi all,

Im hopping some one can help with this we have recently picked up our V35 350GT8 2002, Most of the time the car is fine but twice the car has been on the Highway and twice the car has appeared to start slipping, ie. revs increase but the speed does not to the extent that the car is doing 100klm/h and doing 4500rpm (there is still drive there) at which point I pulled over let the car sit for a minute then once we had taken off it was fine.

Has any one heard of this before???

Link to comment
https://www.sau.com.au/forums/topic/238438-v35-cvt-box/
Share on other sites

Hi all,

Im hopping some one can help with this we have recently picked up our V35 350GT8 2002, Most of the time the car is fine but twice the car has been on the Highway and twice the car has appeared to start slipping, ie. revs increase but the speed does not to the extent that the car is doing 100klm/h and doing 4500rpm (there is still drive there) at which point I pulled over let the car sit for a minute then once we had taken off it was fine.

Has any one heard of this before???

Without specifically knowing anything about that box, I suggest you need to find out what oil you need, as this could be an issue.

As per a Motorbike with a wet clutch plate, the wrong oil can cause no ends of problems, especially slipping.

If you have the wrong oil you can destroy these clutch plates and from how I understand the box is not that well known in Oz, as for repairs!

Research the oil and make sure that is the type inside, would be my first step.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/238438-v35-cvt-box/#findComment-4168403
Share on other sites

Without specifically knowing anything about that box, I suggest you need to find out what oil you need, as this could be an issue.

As per a Motorbike with a wet clutch plate, the wrong oil can cause no ends of problems, especially slipping.

If you have the wrong oil you can destroy these clutch plates and from how I understand the box is not that well known in Oz, as for repairs!

Research the oil and make sure that is the type inside, would be my first step.

Thanks Stephen,

I will do that but its not so much a case of slipping but when this happens it it slike its decreasing the gears available and it wont flip to manual mode

Link to comment
https://www.sau.com.au/forums/topic/238438-v35-cvt-box/#findComment-4168423
Share on other sites

when was the last time it was serviced and what oil was put in?

to my knowledge they use a special oil. its been covered here a few times now.

general consensus on the CVT is to stay away from them when buying for that reason.

lately I have been seeing cheap sedans only to find they are all CVTs with I figure half dead boxes.

Link to comment
https://www.sau.com.au/forums/topic/238438-v35-cvt-box/#findComment-4168487
Share on other sites

maybe its not the gear box, maybe theres an issue else where, the car will only drive in 3rd gear when in limp mode, ie theres a major issue somewhere, 100kmph at 4500 kinda sounds like 3rd gear

Yes that sounds about right Pete,

any ideas what would make it go in to limp mode after being driven for some time with no issues then to do it only on very odd occasions ??

Link to comment
https://www.sau.com.au/forums/topic/238438-v35-cvt-box/#findComment-4168970
Share on other sites

when was the last time it was serviced and what oil was put in?

to my knowledge they use a special oil. its been covered here a few times now.

general consensus on the CVT is to stay away from them when buying for that reason.

lately I have been seeing cheap sedans only to find they are all CVTs with I figure half dead boxes.

Thanks Chris,

Have you heard of this specific porblem before??

Link to comment
https://www.sau.com.au/forums/topic/238438-v35-cvt-box/#findComment-4168976
Share on other sites

Yes that sounds about right Pete,

any ideas what would make it go in to limp mode after being driven for some time with no issues then to do it only on very odd occasions ??

I'm guessing and if it isn't Oil (which is my number 1 pick) and without seeing the wiring diagram but a loose or bad connection and/or faulty speed sensor or input to the Gearbox Computer.

Could be a multitude of stuff unfortunately, but you have to start with the easy stuff first such as Oil and then check continuity of all the connections...

Link to comment
https://www.sau.com.au/forums/topic/238438-v35-cvt-box/#findComment-4169003
Share on other sites

Just wondering if it occurred when you're happening to go downhill? It may be of no help but when I'm at 60km/h down a slight slope (albeit a short one) I tend to let my foot off the accelerator and let the car cruise by itself. The car tends to increase its revs slightly (to around 1500 if I can remember, from the normal 1100/1200rpm) until it reaches a falt surface where the revs drop back to the normal 1200rpm. If so I think it's just a normal occurence.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/238438-v35-cvt-box/#findComment-4169146
Share on other sites

Hi Just to share my point of view. As you all know, CVT(Continuously Variable Transmisson) box have no gears in it. The Jap box usually use a belt to run on the 'virtual' 8 gears. I know there is quite a few porblem with the CVT box from Honda. The CVT box is design for city use and not for hard acceleration. The CVT in AUDI's cars (Muliti-tronic) are different too, they do use a series of gears but they are chain driven. From the description of the problem when driving above 100km/h, I believe the belt will tend to slip. That why if you keep pushing, it will just slip more. I think it's best to let someone to look into it for you. And BTW, they do have a Torque Convertor in a Nissan.

Edited by FlyingEL
Link to comment
https://www.sau.com.au/forums/topic/238438-v35-cvt-box/#findComment-4169808
Share on other sites

when was the last time it was serviced and what oil was put in?

to my knowledge they use a special oil. its been covered here a few times now.

general consensus on the CVT is to stay away from them when buying for that reason.

lately I have been seeing cheap sedans only to find they are all CVTs with I figure half dead boxes.

Spot on.

If you use anything other than the factory recommended Nissan Gearbox oil for the CVT, its history.

Replacement costs are not friendly either.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/238438-v35-cvt-box/#findComment-4170087
Share on other sites

Hi Just to share my point of view. As you all know, CVT(Continuously Variable Transmisson) box have no gears in it. The Jap box usually use a belt to run on the 'virtual' 8 gears. I know there is quite a few porblem with the CVT box from Honda. The CVT box is design for city use and not for hard acceleration. The CVT in AUDI's cars (Muliti-tronic) are different too, they do use a series of gears but they are chain driven. From the description of the problem when driving above 100km/h, I believe the belt will tend to slip. That why if you keep pushing, it will just slip more. I think it's best to let someone to look into it for you. And BTW, they do have a Torque Convertor in a Nissan.

Nope - the V35 uses a very different type of CVT gearbox - they call it the 'Extroid CVT', basically uses a sliding set of angled gears to acheive the same thing as a belt.

http://auto.howstuffworks.com/cvt3.htm

The rest of the Nissan range uses a belt type CVT (Murano, Maxima etc).

Getting back to the original problem, these guys might be able to help:

http://www.cvt.co.nz/index.htm

They're pretty much the only ones in this neck of the woods that know anything about the Extroid CVT, the Nissan dealers will likely only be familiar with the belt type.

Sounds like the gearbox controller is detecting something wrong with the gearbox and putting it into 'limp' mode. Not sure if there is a diagnostic mode for the controller that might allow you to work out what is wrong? When it gets into this mode does it flash anything on the dash cluster?

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/238438-v35-cvt-box/#findComment-4172104
Share on other sites

Nope - the V35 uses a very different type of CVT gearbox - they call it the 'Extroid CVT', basically uses a sliding set of angled gears to acheive the same thing as a belt.

http://auto.howstuffworks.com/cvt3.htm

The rest of the Nissan range uses a belt type CVT (Murano, Maxima etc).

Getting back to the original problem, these guys might be able to help:

http://www.cvt.co.nz/index.htm

They're pretty much the only ones in this neck of the woods that know anything about the Extroid CVT, the Nissan dealers will likely only be familiar with the belt type.

Sounds like the gearbox controller is detecting something wrong with the gearbox and putting it into 'limp' mode. Not sure if there is a diagnostic mode for the controller that might allow you to work out what is wrong? When it gets into this mode does it flash anything on the dash cluster?

good work and great advice...

still think the first step would be ensuring the right oil is inside.

Edited by Stephen Thorpe
  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/238438-v35-cvt-box/#findComment-4173643
Share on other sites

  • 4 weeks later...

My cousin is having the exact same problem on his 2003 v35 sedan with 8speed CVT.

He can't get the car to change gear, and the engine seems to not like revving over 4,500rpm. I believe that the car is in limp mode.

The oil hasnt been changed to the nissan cvt one. Would we go into the dealers and ask for another models car gear oil (e.g another nissan with CVT) and just buy the oil from that...?

Any help would be appreciated. It has been off the road for a while now.... Your help is greatly appciated

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/238438-v35-cvt-box/#findComment-4226227
Share on other sites

Take the car back to who ever you bought it off as their are issues with high klm GT-8's and tell them to sort it, the oil is $1,500 and $26,000 for the gear box from Nissan Australia (last time I checked Nissan Japan don't stock them).

They overheat which causes a few issues but the materials used are not up to standard as they have various failures, the guy in NZ repairing them makes his own parts that have failed as they are not available Ex Nissan.

I can go on all day about why they fail, why the were released in Japan only and other problems but just do a search and everything is mentioned.

Link to comment
https://www.sau.com.au/forums/topic/238438-v35-cvt-box/#findComment-4226913
Share on other sites

  • 5 weeks later...

Thanks for all the advice guys.

Took it back to the dealer and they said thery could not fault the box but, They SAY they changed a solanoid, but they couldnt produce the solanoid (convenient)

By the sound of things they are hopping the car will be out of warranty by the time I have a BIGGER issue

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/238438-v35-cvt-box/#findComment-4290102
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • New CAS just turned up from NZ Wiring. Looks like a nice bit of gear.  So, yeah. Triggered, bro. Realised I may as well do the cam belt while mucking about with it so will order one of them.
    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
×
×
  • Create New...