Jump to content
SAU Community

Recommended Posts

hey guys, got a little problem with my rb20 its getting a little bit hot.

idles around 78-82 which is okay but when i hold the the revs for a while the temps skyrockets... i can be on the freeway doin 80ks and the temp will be 95c on a 15 degree day! but as soon as i take my foot of the throttle and let it coast it drops down to 80ish.

the coolant was flushed 20000ks ago so should be fine

i did a little poking around the engine bay and found that the turbo water line thats behind the block was farked, i changed it but still no change.

im planning on changing the radiator pipes and doing a flush but i honestly doubt it will do anything...

im pretty confident its been bleed properly but its hard to be sure! im getting the temp readings from a nissan consult thing so i suppose its possible the sensor is farked but i doubt it...

thinking about the thermostat but it seems to be opening ok when it gets up to temp.

just really want to get this fixed before summer!!!

any ideas?

Link to comment
https://www.sau.com.au/forums/topic/238456-overheating-problem/
Share on other sites

Sounds like the radiator is partially blocked, just cause they've got coolant in them doesn't mean it won't block up over time. Had the exact same problem with an old Ford and I dicked around replacing everything else but as soon as I put a new core in the problem was solved.

Check your plugs heat range, check oil level. Check radiator, How's your oil pressure? Could also be a blown head gasket.

plugs are good maybe 4000ks old still should be fine they are the correct heat range.

oil lvl is fine but does need to be changed which will be done this weekend.

radiator lvl is fine and i have replaced the cap.

not sure about oil pressure, don't have a gauge.

doubt it would be a headgasket, coolant seems fine, but ill check the oil for water when i change it this weekend.

could be the water pump but when i have the cap off and give it a rev you can see the water moving, and it looks like its moving alot faster than my mates rb20 whos water pump is only 30000ks old....

i reckon ill have to swap the radiator and thermostat and go from there, dont really want to do the water pump looks like a big job.

what do people think of those cheap china radiators, ISC sells them for $299

http://www.skylinesaustralia.com/forums/Is...rs-t216102.html

i figure its going to cost close to $200 to get mine flushed and tanks replaced so may as well go new?

Not sure about it being the water pump. If the pump was stuffed bad enough to be causing that kind of temp fluctuation then the bearing would be howling like a stuck pig.

Rough check for thermostat is to drop it in a saucepan of water and bring it to the boil, the stat should open before the water boils. If you have a suitable thermometer you can check the exact operating temp of the stat. Note...thermometer must be one thats rated for cooking.

Pull the radiator and have it checked by a specialist. If they think it can be fixed properly then stick with that one and not the China version. Nissan's OEM gear is HIGH quality.

Not sure about it being the water pump. If the pump was stuffed bad enough to be causing that kind of temp fluctuation then the bearing would be howling like a stuck pig.
Usual problem is the fins rust away off the impeller. Coz the japs don't like using "green stuff".
Usual problem is the fins rust away off the impeller. Coz the japs don't like using "green stuff".

yeh when i bought it there was fark all coolant in it, mostly water... the radiator pipes are full of rusty shit, im gonna do the thermostat tomorrow and if its still no good ill get the rad looked at and if that doesn't work ill do the water pump and may as well do timing belt to.....

so i did the thermo today, old one looked okay so i put them both in boiling water couldn't get the them to open... must not have been hot enough but i put the new one in anyway, ill test it tomorrow when the gasket goo dries..

does anyone know an easy way to change this hose its the small black one thats circled, it looks like im gonna have to pull the plenum off....

post-22242-1223114891_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Haha, i kow right? Could have bought so many cars for the same amount of money (or less) but driving Unicorn gives you at least +1mln to style 😅. Like wise man said "life's to short to drink cheap wine and drive boring cars" 😉
    • Newbie here, proud owner of an Autech 260RS. I'm on the hunt for wiring diagrams specific to the 260RS, particularly S1. I've ran my eyes through R33, R34 Diagrams, there are some similarities, however continue to find incorrect wire colours and pins on connectors in the 33,34 diagrams.   I was hoping someone could point me in the right direction? I'd be happy to pay for the originals in Japanese. I can translate them, at least they would be accurate.   Any help please would be greatly appreciated, never heard an RB26DETT before let alone driven one, and I've got a spaghetti monster of goodness to sort out.   Cheers Benny  
    • Hey all  im wondering if you can help me please I have put a rb20 box in my r34 gtt as my auto packed up and a friend had a spare box I know it’s not ideal but it will get me up and running for now. we have done the conversation and everything is working great but my Speedo we got a s13 speed sensor but my Speedo reads double now and I bought a speed converter but still not having any luck.  so I thought I’ll reach out and pick your brains  any help would be appreciated please as I wanna drive my car again 
    • Drain it. I got official Matic D but you can get whatever is listed as Matic D compatible.
    • Thanks guys,  Yeah I should at least have them dynoed, at least then I know what I've got as a starting point.  The springs on these are hard as rocks. I vaguely remember Russman saying he was going to sell the shocks to me with the rocks fitted, as he was keeping the softer springs for his new setup.  I didn't click at the time but of course that was to let me know the shock/spring wouldn't be matched.  I also remember pricing up new springs around 2014-15, but, house, money etc. it never happened. So that was another reason to have them rebuilt. I have rebuilt the forks on many motorcycles so I think I could handle the seals on these easily enough, but getting the valving right would be a rabbit hole I cbf exploring.  Duncan, interesting to hear RP was tuning these back then. I might give them a call.  In the mean time I have been busy fitting sway bars. The Whiteline rear sway bar I purchased 15 years ago finally got fitted, along with the Whiteline front bar that showed up last week. Just waiting on new links for the front sway bar to finish that off.  And my spare set of advan AVS VS5's should be back from the powder coaters in a Pearl White finish sometime this week, with a set of Hankook RS4's lined up for fitting.  And then I just have all the suspension bushes to do. A comprehensive kit is on the way... Lots to do before the Ararat hill climb. Cheers guys 🍻   
×
×
  • Create New...