Jump to content
SAU Community

Recommended Posts

take all the obvious bolts off, then there is a bracket right under the parker that is bolted to the chassis by one hex bolt. the bracket is secured to the headlight assembly by two phillips screws but i wouldnt advise undoing then as you will probably snap the plastic location pin so just leave it attached to the housing when taking out.

someone should do a sticky on this subject, as well as parker bulb replacement..lol

ah just re read your post. indicator clips in so take the plastic guards out from the wheel arch and pop it out from behind by squeezing the clips unitl it pops out. i dont remember any screws from memory, though there might be one, but i doubt it.

I just changed the indicators myself, you wont need to take the inner guard lining off. Using your finger tips, pull the indicator towards the front of the car. It will move a few millimeters, then pull it out towards you. It will pop out. Seriously, it only takes a few seconds to do. I was surprised myself.

As for the headlights, i've been searching for a good tute on how to remove them. I've heard that you need to remove the front bar to get to a bolt, but im yet to see pics.

you dont need to take the front bar off for the headlight. just like the indicator you can access that bracket bolt i was talking about by removing or bending the plastic wheel guards and taking to it with a wrench. its that one bolt underneith the parker that holds it to the chassis

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...