Jump to content
SAU Community

R34 Gtt Rear Spoiler Enquiry

PJF

By PJF,
in Exterior & Interior Styling

 Share

Recommended Posts

PJF Community Regular

PJF

Posted
Posted

Hi-- The rear boot spoiler on my two door 34 gtt has a bit of movement in it. I checked the nuts that secure it and there tight. Can anyone tell me if there is supposed to be a rubber pad or some other material that sits between the boot spiler and the boot lid itself. Appreciate any help

Thanks

Carey

Link to comment
https://www.sau.com.au/forums/topic/238851-r34-gtt-rear-spoiler-enquiry/
Share on other sites
Dal34 Collaborator

Dal34

Posted
Posted
Hi-- The rear boot spoiler on my two door 34 gtt has a bit of movement in it. I checked the nuts that secure it and there tight. Can anyone tell me if there is supposed to be a rubber pad or some other material that sits between the boot spiler and the boot lid itself. Appreciate any help

Thanks

Carey

Hi,

When i rippedo ff the spoiler off my gtt, there was a thick layer of double sided tape that was stick on the bottom of the spoiler and the boot.

Hope that helps.

vic_sky33 Enthusiast

vic_sky33

Posted
Posted

i took mine off too, you should find some tacky sponge like layer that holds it down , if not it moves than someones already removed or played with your spoiler. try your local panel shop, they can give you some of that sponge stickt crap and try re sticking it

CR34M Community Regular

CR34M

Posted
Posted
They move.. its just the way it is .. better than it bending the shit out of the bonnet.

FYI it does break off mines reached very high speeds.

I have been to 180 and havn't seen any movement, rattling, nothing at all at that speed straight line for a good 2 minutes at 180.

Unfortunately i have a speed limiter so i can't reach a higher speed to know if my spoiler will rip off haha, but it shouldnt come off at speeds higher than that anyhow! Plus you'd hope aerodynamically at any higher speed that your spoiler would help you keep some sort of downforce if anything. not fall off....then again they arn't exactly made for downforce but none the less they should do something, but definately not fall off.

I'd say what the guys above already have said and that is to just get some strong adhesive that will keep it in place or if you really love your spoiler, resin is your best friend :bunny:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By GTSBoy · Posted

      That's hilariously putrid!
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Well this shows me the fuel pump relay is inside the base of the drivers A Pillar, and goes into the main power wire, and it connects to the ignition. The alarm is.... in the base of the drivers A Pillar. The issue is that I'm not getting 12v to the pump at ignition which tells me that relay isn't being triggered. AVS told me the immobiliser should be open until the ignition is active. So once ignition is active, the immobiliser relay should be telling that fuel pump relay to close which completes the circuit. But I'm not getting voltage at the relay in the rear triggered by the ECU, which leaves me back at the same assumption that that relay was never connected into the immobiliser. This is what I'm trying to verify, that my assumption is the most likely scenario and I'll go back to the alarm tech yet again that he needs to fix his work.      Here is the alarms wiring diagram, so my assumption is IM3A, IM3B, or both, aren't connected or improper. But this is all sealed up, with black wiring, and loomed  
    • hardsteppa
      Hi everyone.

      By hardsteppa · Posted

      Ceste, jak se mas Marek...sorry I only have english keyboard. Are you a fan of Poland's greatest band ever?   
×
×
  • Create New...