Jump to content
SAU Community

Recommended Posts

Hi everyone, got a small problem.

On cruise, my oil pressure is usually around 800 KPa at bout 3grand, and now, when i boost it, not to the boards, jus high revs and about a bar, it gets to a point where it drops to 600 then 400 and I back off.

This is bad and it never did it before, usually always stayed at 800.

The oil is smack on H. When I free rev the engine, its stays at 800.

So I overfilled by 0.75L, and its not dropping anymore when boosting, but this is just a bandaid fix.

I dont believe there is anything wrong with the engine itself, ie bearings and oil pump etc, as the engine is 8000km old and built by the best.

I do have a set of tomei baffles in the sump. Is it possible the rubber flaps have failed? But if they have, would it cause this? Just thinking from factory there are no flaps or gates etc.

A crack in the oil pickup?

I know im probably going to have to pull the sump off, just trying to get some insight first.

Cheers,

Mat.

Link to comment
https://www.sau.com.au/forums/topic/238968-dropping-oil-pressure/
Share on other sites

The oil is 500km old. Its the same oil ive been using in the engine since the rebuild, and havent had a problem until now. So I doubt the oil would have much to do with it?

There is full pressure during free revving (car stationary) as stated above. If there was a problem with the oil im using id have low pressure all the time? Correct me if im wrong. Im thinking more towards this being a starvation problem.

I have notced my gauge seems to drop really low at times, i have put it down to the sensor or gauge not reading right, but if i was you i would take it back to who ever built the engine just to be sure, if they didnt use new sensors and oil pump on the rebuild then they deserve to have to pay for it now.

Its Ausfield Extreme Synthetic, i think its a 5w50. Like I said, ive had no problems until now. And it wasnt doing it immediately after the oil change if you were thinking a bad batch of oil or something.

The readings are off my defi guage which is also 8000kms old so no issue there.

I will be contacting the builder later this week when im not working till 530, thought id get some opinions before then.

Cheers for the help so far.

Every modified GTR should be run with an extra litre in the std sump.

I thought this was common knowledge by now......

This is the first I have read about it, but if that's true I need to go put another litre in mine. But how would that effect his oil pressure? or is the extra oil just for impurities from a recent build?

Edited by James_03

Well I thought that overfilling was for modded and tracked GTRs without baffles of some sort...and I wouldnt have thought if you didnt that it would cause this problem but anyways, problem sorted I guess.

Cheers Ben.

Every modified GTR should be run with an extra litre in the std sump.

I thought this was common knowledge by now......

But, does this apply to track only? And is it the same if you have an oil catch can? Wouldn't the extra oil just go into an oil catch can? (sorry, my mechanical knowledge is not the best)

But, does this apply to track only? And is it the same if you have an oil catch can? Wouldn't the extra oil just go into an oil catch can? (sorry, my mechanical knowledge is not the best)

The problem with these and gtst's (worse on gtst's tho) is that there is not enough drainage from the head to the sump, add to that a big volume oil pump and constant high revs and before you know it all the oil is somewhere around the head, from what i have read there is no harm in putting and extra .5 ltr of oil in for daily use but for track use and extra 1 to 1.5 ltrs is best, i put an extra .5 ltr in my gtst and it does not have any blow by.

Whilst for normal driving it is not really needed it does not hurt to put some extra in for those "excitable" moments :blink:

Edited by W0rp3D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm looking for some real world experiences/feed back from anyone who has personally ran a EFR7670 with a 1.05 exhaust housing or a .83 I'm leaning towards the .83 because its a street car used mostly for spirited driving in the canyons roads. I"m not looking for big numbers on paper. I want a responsive powerband that will be very linear to 8000 rpm. I dont mind if power remains somewhat flat but dont want power to drop off on top. The turbo I've purchased is a 1.05, although the mounting flange T3 vs T4 and internal vs external waste gates are different on both housings, I not concern about swapping parts or making fabrication mods to get what I want. Based on some of the research I've done with chat gpt, the 1.05 housing seems to be the way to go with slightly more lag and future proofing for more mods but recommends .83 for best response/street car setup. AI doesn't have the same emotions as real people driving a GTR so I think you guys will be able to give me better feed back 😀   
    • Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
×
×
  • Create New...