Jump to content
SAU Community

Recommended Posts

Need quick replies please, i'll be doing this today!

I am putting some aftermarket gauges into my car:

Water temp, Oil pressure & Oil temp.

I already know that i can't remove the factory water temp sender near the thermostat housing, as this reports back to the ECU the engine temp. I've already had a friend fabricate an alloy "T" pipe to splice into the top radiator hose, with a fitting welded onto it to take the water temp sender. That's sorted...

But...

Would i be interfering with the ECU or car in any way by removing the stock oil pressure sender (just below the inlet plenum & AAC valve) and stock oil temp sender (behind the oil filter and close to the block) and fitting the senders that were supplied with the gauges?

I was feeling pretty confident that it was ok, before i had a closer look at noticed alot more wiring than i thought there'd be coming from these senders in the wiring loom...

Thanks for the quick replies in advance.

Link to comment
https://www.sau.com.au/forums/topic/23920-aftermarket-gauges-r32-gtr/
Share on other sites

Hmm, 31 views, no replies, thanks guys! :D

At least you can learn from my experiences here:

Well, i've fitted the oil pressure gauge with no problems at all, works well. Much better than the original gauge that has all sorts of problems reading accurately.

Only problem i did come across was that the OE Nissan oil temperature sender is a VERY obscure thread size. A very rare M12x1.25 thread. Realising that a 1/8"NPT threaded sender won't fit, i went to my local Enzed and had no luck with getting an adaptor. Same story at Pirtek, they said only M12x1.5 thread is the most common and doesn't even come close..

Plan B, decided to test the original Nissan sender against the sender supplied with the gauge. This involved getting out my multimeter, digital thermometer and tested the resistance of both senders at different temps in a saucepan of water on the stove!! :bahaha:

No good there, the senders both having completely different ohm ranges.

Plan C, tried looking through VDO's catalogue for an appropriate sender. Turns out that their only sender in the thread that i was after also had the wrong ohms range.

Looks like the oil temperature gauge stays off for the time being until i can figure out a way to get an adaptor fabricated or find a suitable means of fitting this gauge.

Any suggestions?

  • 2 weeks later...

I hate to bring back my own thread again, but, don't you hate it when you spend the time, money and effort in engineering a one-off part to do something (in this case an adaptor for a water temp sender) and you could have bought something like this:

hose_atc.jpg

But my reason for this post, was whether anyone has seen this oil filter sandwich adaptor for sale anywhere here in Australia? It would help me alot if i could get ahold of this product to help hook up my oil temperature gauge (as i discussed above):

sensor_atc.jpg

The following pic, you can just make out that it's the threads i need, M12x1.25 and 1/8"NPT.

It will need to suit the thread of the oil filter to suit an R32 GTR as well.

sensor_ill.GIF

Thanks.

  • 2 years later...

I ll bring this thread from dead again, for people's future information. Ring Mark from Motorsport Connections in Seven Hills, they can manufacture an adapter for oil/water temp/pressure.

Addr.: 15/4A Foundry Rd, Seven Hills

tel.: 98387272

I haven't had mine done yet (waiting for oil change). I ll post how I wen when they are done.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
    • Any going to watch World Time Attack at SMSP this year?
    • Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...