Jump to content
SAU Community

Recommended Posts

So I recently destroyed my Garret GT30/71R (I think it sucked in a small dog or something).

Myturbo2.jpg

So instead of spending large amounts of cash rebuilding it, I am considering an upgrade...

I have the following mods done to my RB25DET:

- A'Pexi Power FC

- Splitfire coilpacks

- 550cc Sard injectors + 044 fuel pump

- Turbosmart Supersonic BOV

- JJR Front Mounted intercooler 300x600x76

- Trust Power Extreme ll 3" full exhaust

(I will also be installing a GReddy Profec B Spec ll boost controller)

Using the previous turbo the car made 240kw at the wheels, I would like to see it make 260 - 270kw on a safe tune.

I am looking for experienced peoples opinions on what turbo I should get.

I am also going to use the standard exhaust manifold so high mount and/or external gated turbos are out.

Any help will be much appreciated,

Thanks :)

In my original post I said that I am not looking for high mount and/or external gate... But thanks :P

sorry for my ignorance :P

well my friends R33 has a low mounted GT3040 on factory manifold and is making around 270kw at the wheels on around 1.3BAR with cams and PFC.

Edited by dmr
No problem :P

I didnt think that you could low mount a GT3040 (I thought that they were too big), but anyway... Would a turbo that size be very laggy? I dont have aftermarket cams in mine either.

no idea on how he got it to fit, he brought the car with the turbo previously installed. he gets full boost at around 5,500rpm.

i fit a TR43 (almost same size) on my RB20 low mounted. i had to grind back a millimeter of the manifold and rotate the turbo housings a couple degrees.

Edited by dmr
GT35... look below for my results...

I had my GT35 low mounted on my customised factory manifold...

if you want a big turbo it's a good choice...

Not bad at all, Im assuming that the GT35 is external gate?

no idea on how he got it to fit, he brought the car with the turbo previously installed. he gets full boost at around 5,500rpm.

i fit a TR43 (almost same size) on my RB20 low mounted. i had to grind back a millimeter of the manifold and rotate the turbo housings a couple degrees.

Sounds like it could be an option, I think I would prefer to have something a bit more responsive though. The GT3071 had almost no lag at all :P

going the hks route will be very expensice but the 2835 pro is great.

Garret is the way to go but to get that power with a good setup you will need a external wastegate as the internal setup doesn;t work so well with the garret turbo's.

So I recently destroyed my Garret GT30/71R (I think it sucked in a small dog or something).

Using the previous turbo the car made 240kw at the wheels, I would like to see it make 260 - 270kw on a safe tune.

The turbo you have should do that.

So just rebuild it, problem solved. If you CANT make that power something isnt right with the setup.

The 3071 is the perfect choice!

GT3540?

Why put a 700hp turbo on a car thats only after less than 450hp? stupid suggestion

In my original post I said that I am not looking for high mount and/or external gate... But thanks :P

You can actually get them with internal gates, no problem there... however again, its a dumb turbo choice as is a GT3040 even in the 500hp form (with the smaller comp wheel)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...