Jump to content
SAU Community

Recommended Posts

  • Replies 61
  • Created
  • Last Reply

Top Posters In This Topic

You after standard piping??

If so then yes I have a full set in good condition and not shrunk.

I have a good condition GTR fuel pump yes.

No injectors or turbo though

hey mate

interested in all the inner quarter window surrounds nd also the front ones as well nd do u ave any pics and will u do postage 2 4505 also how much all 2gether

cheers matt

Tein R32 GTR coilovers HA Coilovers removed from an R32 GTR. They are the adjustable HA version Tein's. Height adjustors all work, no oils leaks or other damage to the shocks. They came in a car I bought and since Ill be fitting a my proflex suspension I have no need to keep these. Im not sure of the age but id say they not all that old $850ono

Everything is located in Sydney

Hi there just wondering if you have the Tein coilovers still 4 sale?

If so you think you can send me a photo of them, you say there in good condition?

What's your last price on them?

pm sent

replied

hey mate

interested in all the inner quarter window surrounds nd also the front ones as well nd do u ave any pics and will u do postage 2 4505 also how much all 2gether

cheers matt

The trims are slightly damaged however the fronts are perfect condition

Hi there just wondering if you have the Tein coilovers still 4 sale?

If so you think you can send me a photo of them, you say there in good condition?

What's your last price on them?

Yes I do still have them, They will be removed this weekend so can take a few photos of them then. Yes they are in perect condition and still look pretty new to me.

Price I have listed is lowest im prepared to take otherwise ill keep them as spares.

hey Brad, dont have any of the metal intake pipes for the front of the compressors do you? I think i need a front one at least to do my piping how i want it. cheers

Yeah Jeff I have a complete set of RB26 intake pipes that have come from my race car.

Ill put them aside for you.

For yours I think you'd be best off using front and rear GTR intakes and making alloy intake pipes from there.

Jeff your welcome to come past any time that your not going to infect me with disease!

On that note I was meant to come get stuff from you this week gone.

Sorry no drivers door rubber

I have everything you just listed besides the Hangers.

Tank with filler neck $150

Pump/sender $150

I dont mind sending to Brisbane if you organise everything from your end and I just need to wrap it onto a pallet ready for the truck.

Brad...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...