Jump to content
SAU Community

Recommended Posts

well in Japan they have a differne type of gas than is used over here!! the aircon can be filled with normal gas no worries, just have to pay extra to dispose of the old gas!! But should have been swapped over during compliance!

retro fit is not part of complience.

R12 is not illegal to use.it is for sale.and can be used.WHY BOTHER.i havnt seen a can that needed it.if the pressurse were funny/high it mostlikly needed a newTX valves and replacments are R134A set.

to retro fit you replace the reciever dryer[filter] and the new ones are R134A compatible.service valves adaptors[not needed].

OIL[important] if you use other oils or drop in gasses these can effect hoses and orings and worse clean out the scum on the inside the pipes from the old gass and cheep oil.

if you use PAG type oil you dont.its a good idea to replace oring anyway as high pressure tend to melt them.

R12 is over $100 a kg [about the amount you need]

R134A is around $10-25 KG and good oil is up to $40.[need 150/200 ml.

WHY BOTHER with blend gas or hydrocarbon..

panel shops and electricians use all sorts of fad gasses.these still have R12 in them.SP43F is from memory flavour of the month.This is very good in houshold goods im told.

the problem is the oil.ROCK OIL is the common type and aunty ESTER. VERY GOOD IN FRIDGES.

if they were good in cars then the factory would use them.

speaking of regassing, ive got an R33.. takes R134A.. Got it regassed as it started to heat up at the start of last summer.. I use AC only every now and then (robs power) - thought today I would chuck it on AC as it was quite a nice day, and its barely cold :D

the idea of climate control is you leave it turned on.

when not in use it will leakout.compressor seals ect.

6 months.I would say you got a leaking bit,have a good look for oil stain on pipes and conections.oil on the front hub of compressor will indicate shaft seal.

its normal to get small leaks on the cold side of a/c.as they are cold/wet most of the time corrosion and cracks are comon.

ive replace evaporators TX valves and compressors on R33.

leaks on the high pressure sise are normally works today stuffed tommorrow.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
    • I hope that is not something that bad. From what i remember he said that only first gear is "hard" to get in and that he has couple of ideas what to try next but idk 😕  hope it is not gearbox out. I will let you know.
    • If it's not the hydraulics, it is probably gearbox back out. Usually as per @Duncan's post, or otherwise associated with not getting the throwout fork positioned correctly. All the way up to catastrophically bolting shit back together without it being aligned properly and wrecking the clutch/input shaft/flywheel/something else.
×
×
  • Create New...