Jump to content
SAU Community

Recommended Posts

Hi, i get a rattling sound -I think its coming from my exhaust- at about 40k's.. when im revving it.....

when its on neutral it doesnt make the sound, only when im driving... i recently got my cat converter replaced so its not that, my muffler replaced (i thought it was that but it wasnt) so now i have no idea what it is and my mechanic doesnt know either.. any ideas? thanks

You would think itd be something like that, theres not much else it could be if its comming from lower areas near the exhaust :S

You said you replaced the cat and wasnt that, did they check the piping from the extractors etc? maybe something isn't holding/stuck there.

But the word rattling in general is quite broad without hearing the noise for ourselves...is it a deep rattling noise? A tinny rattling?

I don't know much myself but if it doesn't happen when your idling but happens around 40km/h and continues it could just be that a section of piping is loose and not held in place properly, and when more pressure is passing through, the noise therefore occurs??

I could be waaaay off the mark. Goodluck hope you get it resolved soon!

mines doing the same aswell and its a r33 like all of you, i sware it comes from the gear box........

i think it is bearings somewhere that are worn down?

the sound and where its coming from sounds like a bearing, are all of you getting the same rattle from the gearbox thats really deep at 1500rpm and once it hits 2000rpm its more of a quiet tin rattling sound then stops after 2000rpm.

anyone confirm that they think its bearings now

yeah. sounds like a deep rattle O_O it sounds like its coming from the exhaust to me (but it aint cos i got it checked out) Anyone HOW MUCH DOES IT COST TO FIX MORE IMPORTANTLY? aNYONE KNOW? APPROX?

I'm getting the exact same problem in my R33 SI GTS-T..

I just finished installing a FMIC (which was a bitch, damn clamps flying off) and only just started noticing it now that I'm listening extra carefully..

I did some diagnostic and noticed that if I push my clutch in while it's rattling the rattling immediately stops. I was in second gear, stock ECU.

Edited by Alinys

if it stops when you put the clutch in it could be the trust bearing but id be dam soprised if you could hear that making noise while ur actually driving! when sitting there ideling you can normally pick it because it will sound like something mechanical rattling around and when you push the clutch in it stops.

but i doubt it would be a thrust bearing.

changing the clutch and all components of the clutch soon (after my 50thou rebuild is back together in a week :P ) so ill soon be able to see if it helped me or if its a problem that nothing to do with manual and auto differences. it might be the cat r the muffler because there relatively close to the gearbox to be mistaken because its just a crazy noise =\

i got the same problems, with the stock muffler it was loud on take off. it rattle hard.

thought it was a broken muffler so i got a a cannon it was still there wasnt that loud tho. i was thinking it was the cat or the resonant

seriously its going to be the clutch or gearbox. THE SOUND IS A DEAD BEARING!!!!!!! thrust bearing probity auto or manual i guess its got to be the same component, that is if were are getting that noise that we all say we have. someone take phone and record it. my car has no engine in it at the moment because of mods so i cant :)

thrust bearing probity auto or manual i guess its got to be the same component

I think you will find that only manuals have a thrust bearing as it only works when with the clutch, i know the noise im talking about is not the thrust bearing as that is making a different noise :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...