Jump to content
SAU Community

Recommended Posts

hey guys and girls i am putting up my track car for sale/swap as i have now got a new job and will not be able to make it out to the track anymore.

specs:

R32 Gtst

S15 SR20DET conversion (completed in japan)

S14 5 speed

211rwkw on 1.2 bar

Power FC and hand controller

OS geiken twin plate clutch ( recently rebuilt )

TOMEI 256 cams

550cc injectors

HKS GT SS turbo ( less than 1000ks done )

N/A SR20 throtlle body

Big internal fuel pump

xforce manifold

rb25 airflow meter

straight pipe

Big TRUST FMIC

GReddy triple core radiator

KAZZ 2 way diff

HKS coil overs

camber adjustable

Brand new Whiteline Adjustable 24mm sway bars front and rear

Brand new Kazama Adjustable Castor rods

hicas lock bar

drift pineapples

SPARCO driver's seat

GTR interior

shift knob

turbo timer

sparco steering wheel

boost gauge

Racing pedals

Strut tower brace

Drift style handbrake

body kit is genuine BN Sport kit

evc 4 set to 1.2 bar

WORK miester 3 peice rims.. fronts 18'' by 10'' and rear 18'' by 11'' new tyres on the rims.. front 255/40 rear 275/40

Full wide kit 30mm rear and 25mm front.

Car is not complied but can be.

looking for around $13,500o.n.o but may swap with cash adjustment either way

post-33385-1226355434_thumb.jpg

post-33385-1226355456_thumb.jpg

post-33385-1226355470_thumb.jpg

post-33385-1226355493_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/244271-sr-r32/
Share on other sites

so by removing the engine and replacing it with a standard rb20? hence removing all the engine mods.

bit misleading to say it can be complied, and not state you would probably have to spend a few thousand to do so.

don't take me wrong, the car is excellent value for the work done and the money it would take to get a r32 to this state. the mod list is impressive to say the least, but wouldn't exactly say it is compliable.

Link to comment
https://www.sau.com.au/forums/topic/244271-sr-r32/#findComment-4254895
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...