Jump to content
SAU Community

Recommended Posts

Guest RedLineGTR
Originally posted by Brody

I just picked up 5 of mobile1 at autobarn for $55? so ill see how I go tomorrow when i change....

Quick question, mobile1 being 5w-50, isn't that going to be 2 thick when warmed up? Thicker = slower revs?

it should be fine...alot of people use it on the forums from what i know..there is also i diff type of mobile 1...0-40w rating hard to get for only workshops from what i have heard. Would be nice to get some..

  • Replies 52
  • Created
  • Last Reply

Top Posters In This Topic

hhmmmm...then would something like castol -R be better as its rated at 5w-30?

I just took out all the black shit that was in there, topped it up with fresh mobile1, took it for a quick spin, didn't really noticed a difference....other times ive had it flushed i have :P

When u do an oil change, do u have to change the filter everytime?

I use a mechanical oil pressure gauge, if all is set up ok there is no rear problem, but unsure of legalities.

Brody, why put $50 of oil in and not spend the extra $8 on a filter just to be sure. Otherwise you still have all the old oil and dirt in the filter with the new stuff flowing through it.

mobil dont cope really well in temp department.

Thats contrary to an article i have (had?) that rated the Mobil1 as having the best high temp stability of all the oils tested (approx 8 oils from memory)

I have used Mobil 1 on this basis and with my engine having done 155,000kms, 3,000 of which have been at prolonged full throttle on circuits... it seems to have peformed well at high temps.

This is a good read, as im looking for a different oil after 6 years of using Mobil1, its getting too expensive.

Your thoughts on using say a 10-50w etc for an engine with higher kms say 155,000kms?

I found little difference between the 2 on the street. Shell was probably better because of it's pricing even temps was only a tad higher, but of no concern.

But on the circuit I like the Mobil 1. Shell, the temp rose to rapidly and went well above 130 degrees. Mobil sat at 115 degrees.

Originally posted by Clint32

Brody, why put $50 of oil in and not spend the extra $8 on a filter just to be sure.  Otherwise you still have all the old oil and dirt in the filter with the new stuff flowing through it.

Because i forgot until i had started :D

its the first time ive done it myself...

You can get mechanical oil pressure gauges but they can't be mounted in the cabin. Hence people putting them on the bonnet.

Electrical oil pressure gauges which use a sender are fine for cabin mounting, but are more exxy and may (as someone said) have a reduced range. However as long as it covers the expected operating point of your oil around the middle of the gauge it'll be fine. I really don't think oil temperature should vary by 140 degrees!! (if base temp is 40C then 180C is your top temp.. fairly hot oil!)

Jay i fitted i remote oil filter and cooler so the filter mount had a spare fitting that i used, otherwise im pretty sure you are able to buy a plate that goes where the filter is and the filter screws to that. Remote filter is not hard to set up either and makes changing the oil very simple.

ahh

well i got a 93 gtst

and i just put helix ultra 5-40 in

and im having the pressure problems aswell

if it doesnt sit above a qtr i get very cautious

but yeah it sbeen in for 2 weeks now

and sits VERY low at times

around 5-6 at startup till its warm

maybe because it runs so hot it flows free'r?

who knows

ill dump it after 2 thou

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...