Jump to content
SAU Community

Recommended Posts

It just occured to me the other night that i noticed the seatbelt icon on my dash(little dude with the seatbelt-on sign) doesn't come on anymore...

cos normally when the driver's side seatbelts aren't buckled in the icon will light up etc etc....now nothing at all....

Anyone had this happen to them? Any ideas what's going on?

thanks;)

Link to comment
https://www.sau.com.au/forums/topic/24551-seatbelt-icon-disappears/
Share on other sites

Originally posted by skyliner33wa

i thought that the seatbelt fastened feature was removed and seatbelts replaced during compliance?

Kris

No only the rear belts are changed. Front ones are factory. Yea check the electrical connection under the seat and then the bulb in the Dash. If that doesn't fix it,,,give up it's not worth working out.

Neil.

Originally posted by ndr

No only the rear belts are changed. Front ones are factory. Yea check the electrical connection under the seat and then the bulb in the Dash. If that doesn't fix it,,,give up it's not worth working out.

Neil.

Pretty sure mine has been changed then, i have had 2 skylines and both times no seatbelt light, are their supposed to be wires, or a connector coming from the seatbelt?

cheers

kris

i want the light!! you guys reckon there would be a way to hook it up?

has anyone check their belts with those from a wreckers without change made!! see if those plugs do actually plug into the clips?

I want the factory seatbelts! :) Well at least for the front, who cares about the rear passengers :)

Incidentally, even though my car was registered as a 4 seater, the compliancers nicely left the middle factory seatbelt in place, but under the seat. The previous owner probably didn't even know they were there :)

Does anyone know if the S14/15 200SX front seatbelts are the same as the R33's? It might be a good way to get some nicer seatbelts legally. Ones that use the seatbelt light, retract properly, and have that plastic thing to hold the belt off your shoulder.

Sorry guy's I should have worded my reponse a little better,,,,what I meant to say is the Fronts have to be changed as well,,,but It's quite legal for the Compliancer to buy New Factory Belts and install them. Thats how most of us still have the light working on the dash. Go check the white tag on your front belts,,,,Mine has Genuine Nissan belts with a built date on it,,being 2001.

Neil.

Originally posted by JimX

Ndr, how much are the new belts worth? Probably several hundred each ;)

JimX,,,I have no idea but mine have 2001 stamped on them and they have to be factory belts,,,.I'm thinking though if the tongue of the actual belt is the same as the buckles (this is what turns the light on and off) then you would only need to buy the buckle. Why not pop out to Justjap and ask them,,,,they might/should have buckles,,,you could try one.

Neil.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...