Jump to content
SAU Community

Recommended Posts

ey, it was raining and i hit the gutter and went over it.. there was no external damage however my steering became alot lighter and it wasnt straight, so basically i had to steer right to go straight.

anyone know what the problem is and how much it is to fix?

Thanks!

ey, it was raining and i hit the gutter and went over it.. there was no external damage however my steering became alot lighter and it wasnt straight, so basically i had to steer right to go straight.

anyone know what the problem is and how much it is to fix?

Thanks!

How hard did you hit it? If your lucky, it might just need a wheel alignment, however, considering that its lighter, not just veering to the left, it could be more serious, bent something etc. I'd probably take it into a Tyre shop and get them to look at it.

ey, it was raining and i hit the gutter and went over it.. there was no external damage however my steering became alot lighter and it wasnt straight, so basically i had to steer right to go straight.

anyone know what the problem is and how much it is to fix?

Thanks!

wheel alignments are cheap.....so thats if your lucky

i recall someone who driften onto the gutter...

which required changing most of the suspension.....if thats the case, make sure u start saving up

had a laugh at your title..lol.

i was driving in the wet once, lost it on a corner over corrected and hit a gutter head on. at least when i hit it i made sure the wheels were pointing straight before humping it. blew a tyre and buggered alignment. only cost me a new pair of tyres and two wheel alignments cause the first place couldnt do the job properly.

take it to a reputable tyre place and get them to check and do a wheel alignment. quite simple really. if somethings broke or bent they will tell you and you will find out how much to fix. they should not fix it without asking you firs tso you wont be surprised with a larger than average bill. I stress take it to a reputable suspension place. if you are in melb i can reccomend you one or two.

i scraped my rim to the max too LOL

i hope its the allignment then,

but its steering alot lighter, anyone know what it is? :S

Also, what about the axle? Few mates of mine say i coulda barred that,

also i buckled a rim, can i buy single ones somewhere?

I'm in melbourne,

IS beaurepairs a good place to go?

Edited by Luckieee

thought u were going to get it looked @ today hence i recommended a tire shop, cos theyre normally open 7days. if you are getting it looked @ during the week , take it to a suspension place that does alignments. where u from?

Like i said if something were to be bent its probably a lower control arm, or steering rack. Hope your rack hasnt snapped?? could explain the light steering. if so i wouldnt be driving.

Just have a look under the front car and inspect

where can i get cheap alignment done? :D

i guess you'r not heeding my adivce to go to a proper suspension place hey?

Traction tyres rowville is where i take my car to or you can try Centreline if your on the other side of town. The guys at Traction tyres are a class act and will tell you what needs to be done to fix things and nothing more. $66-$77 for front and back from memory. Should be cheaper for just a front end alignment.

g/luck with it.

so they got they told u that your control arm is damaged and charged for a wheel alignment!! if your control arm is bent, they wouldn't be able to align your car properly. i would take it elsewhere, ie try the ones recommended by the guys above. and if its confirmed that your contorl arm is bent get it fixed and demand a refund for the dodgy work done @ beaurepairs. if u have any issues call the dept of fair trading or the beaurepairs head office.

if you need a control arm, check out some of the wrecks in the for sale section. or call some local import wreckers.

;) they could have charged you just a small fee to look at your car and see if theres a problem and then go from there but then again your steering was pretty out of wack wasnt it I got TTyres to do to double check the dodgy alignment i got previously before i went ahead with anything.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I was using the wiring diagram I have So 12.74V is coming into the rear Fuel Pump relay as I measured.  When I turn the key to ON im getting 0.6V to the Fuel Pump plug; which i assume is backfeed voltage and doesnt include the 12V from ignition power.  The rear relay is working and being triggered.  From the diagram I clearly see the rear relay 80 = Rear Relay going into the Body/H loom (R-27) 27 = Fuel Pump plug going into the Body/H loom (T-20) 40 = Short Connector (R-27) I'm reading 12.74V on the blue/black wire which is the power for the Fuel Pump   From this diagram I can see the Ignition relay goes into the front and up to the ignition  2 = Fuel Pump Relay <1M> (R-27) 37 = ING Relay <1M> I started from the pump using this reference Which the way I read it (referencing Nissan wiring color codes) is: Pin Wire Color Function 1 B/P (Black/Pink) Ground 2 L/W (Blue/White)        ECU Trigger 3 SB (Sky Blue) Fuel Pump 5 L/B (Blue/Black) 12V Constant Tested SB to SB on Fuel Pump for continuity - confirmed Tested negative on Fuel Pump to 12V battery and L/B - confirmed 12V Pulled the relay putting 12V between Pin 1 & 2 and testing continuity on Pin 3 & 4 - confirmed relay   So that has me looking at this part of the circuit to understand whats happening here...and im still confused. From best I can tell; the disconnect is back to my previous diagram; between Ignition Relay and Fuel Pump Relay...which yet again; afaik is where the immobiliser should.    Thats what I was trying to explain to GTSboy; im not trying to fix it myself; yet I seem to have to get a Masters in Electrical Engineering (while im busy doing my actual job of DevOps & Cloud Engineering) somehow.  I just wanted more expert opinions; or more so that what I tested is correct and proves it to something around that area; to go back to the alarm tech (for a 3rd time) that he needs to fix it. He keeps telling me its not the alarm. He lives on the complete other side of the city so i understand not wanting to make a trip but as I said before if its the alarm it should be up to him to fix it. But he's adament its not; even though I pointed out the FP was immobilised through the original alarm. To my mind; it seems that the ECU is sending the signal; but the ignition is not getting 12V down the line.       
    • Maybe also really stiffly sprung track cars. Get the inside wheel up in a corner and all the fun stops. Also me sometimes (rarely) when I have to stand on the brake to convince the diff to drive the wheel that is still on the ground when I'm trying to diagonally get over severe driveway entrance, etc.
    • I feel like I'm missing something. You had an authorised installer come out and install a new alarm. Post install the car doesn't start, and you aren't getting the installer back to fix what they did wrong?
    • So either way it is gearbox out and look what is wrong?  I know about the input shaft bearing. Even before swap/new clutch the it sounded exactly like this: So is that inout shaft bearing or the other was installed backwards?  And can some please tell me the part number for that input shaft bearing? The gearbox is small box from R34 N/A and number is FS5W71C. Thank you  
    • I am yet to see anyone ever regret a quaife or helical. ...other than drifting/skidpan duties. I kind of want to upgrade my factory helical with a Quaife (but really it's not ultimately that different, and is a MASSIVE UNDERTAKING), that's how good the hype is about them, that I want to try them 'just to see'  
×
×
  • Create New...