Jump to content
SAU Community

Recommended Posts

hey all im in the middle of building a RB26 and am starting to strongly consider selling my 33 and purchasing an old nissan/datson.

was after some opinion of what to look into...

looking at a massive power to weight ratio.

i have thought of the obvious like 1600 and dato ute.. but is there any other wicked old skool cars out there???

and will it fit is prolly a good question..

i no some one has a 30det in a 240z

Dan

Link to comment
https://www.sau.com.au/forums/topic/246555-rb26det-into/
Share on other sites

would love to put my 1000hp GTR engine into a Charger...C4 auto and massive rear slicks.

would run 8's at the strip.

Ive owned 6 Chargers in my younger days they are around 1100kg with the Hemi 6 in them...it would haul ass!!

Link to comment
https://www.sau.com.au/forums/topic/246555-rb26det-into/#findComment-4285731
Share on other sites

Strawberry faced 180SX with an RB30 has always been a dream of mine

So have a 26 powered WB ute!

Strangly, I want to put a TT LS1 in a 33.

Would the engine fit into something crazy like a Navara or Hilux?

Gemini?

Van even?

I could on for days...

Link to comment
https://www.sau.com.au/forums/topic/246555-rb26det-into/#findComment-4286066
Share on other sites

Strawberry faced 180SX with an RB30 has always been a dream of mine

So have a 26 powered WB ute!

Strangly, I want to put a TT LS1 in a 33.

Would the engine fit into something crazy like a Navara or Hilux?

Gemini?

Van even?

I could on for days...

lol @ gemini, when i had my lil gem i was considering a ca18 swap, rb26 would be bad idea haha power to weight plus youd have to cut into the fire wall etc etc.

buy my gf's FTO and put it in that! doo it. :blink:

Link to comment
https://www.sau.com.au/forums/topic/246555-rb26det-into/#findComment-4286674
Share on other sites

old school volvo 240.

That well get some :blink:

Road or drag?

Road some light jap car of your choice

Drag any muscle car that takes your fancy, but you would have been better off with a gen3 v8. Lighter with possibly more potential

Link to comment
https://www.sau.com.au/forums/topic/246555-rb26det-into/#findComment-4286710
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...