Jump to content
SAU Community

Please give advice, i wanted to buy a GT-t R34...

[Tommy_R34]
 Share

Recommended Posts

[Tommy_R34] Rookie

[Tommy_R34]

Posted
Posted

Hi Guys, i wanted to buy this Skyline GT-t R34 but i don't know if it's worth the prices coz i don't really know how much is in the market so please help me out, i'll describe it to you guys, here we go : Nissan Skyline R34 GT-t late 98 Manual, 6 cylinder Turbo, Black, 54000kms, Nismo body kits, GREDDY Trust front mount intercooler, Blitz BOV, Blitz boost controller SBC ID2 , Kenwood VCD TV with TV Turner, Blitz air filter, Blitz turbo timer, Blitz Gauge, Momo Steering wheels, Flash Point Alarm, Turbo Back Exhaust, 6 months rego and selling for $34,000.... it has backfire and then a little bit smoke came out but when the car is park and put on neutral i revs up and have no smoke, is it okay or there is something wrong? please give me your advice if this price is good for this car and it looks really much like the photo i attached.......many thanx.....

Parag0n Mentor

Parag0n

Posted
Posted

HI Tommy,

That price is pretty decent for a R34 GT-T and it has quite a few aftermarket items, maybe you should take it in for a service and get the misfires sorted out ?

Where does the smoke come out ? the exhaust ? the engine ?

franks Veteran

franks

Posted
Posted

this is a really good price!

black smoke coming out of an exhaust is not normal, its overfueling. with my stock ecu in my 34gtt i never had black smoke coming out of it on wide open throttle.

accident damage. hrm..its very rare to find a car (especially an import) without accident damage.

sure its nice to have a car that hasn't been in one, but as long as the chassis is straight, panels can always be fixed/replaced. you should be worrying about the quality of the repair more than anything.

ac1d3o3 Enthusiast

ac1d3o3

Posted
Posted

yeah got a skyline inspected, had a look at it. looked fine to me but they came up with heaps of stuff. theyre really thorough and they give you their opinion about the car. they told me that it wasnt worth buying the car.

probably saved me heaps in the long run.

pentae Mentor

pentae

Posted
Posted

Take it to an a mechanic who mainly does performance cars and imports. Tell him you are interested in buying an r34 and your intentions are to take the vehicle to him for servicing/performance mods.. and could he kindly check that it doesnt have anything wrong with it.

He may do the service for close to nothing to bag you as a future customer.

Rezz Grand Master

Rezz

Posted
Posted
Originally posted by pentae

Take it to an a mechanic who mainly does performance cars and imports. Tell him you are interested in buying an r34 and your intentions are to take the vehicle to him for servicing/performance mods.. and could he kindly check that it doesnt have anything wrong with it.

He may do the service for close to nothing to bag you as a future customer.

Thats probably the best piece of advice ever... well done mate :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By GTSBoy · Posted

      That's hilariously putrid!
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Well this shows me the fuel pump relay is inside the base of the drivers A Pillar, and goes into the main power wire, and it connects to the ignition. The alarm is.... in the base of the drivers A Pillar. The issue is that I'm not getting 12v to the pump at ignition which tells me that relay isn't being triggered. AVS told me the immobiliser should be open until the ignition is active. So once ignition is active, the immobiliser relay should be telling that fuel pump relay to close which completes the circuit. But I'm not getting voltage at the relay in the rear triggered by the ECU, which leaves me back at the same assumption that that relay was never connected into the immobiliser. This is what I'm trying to verify, that my assumption is the most likely scenario and I'll go back to the alarm tech yet again that he needs to fix his work.      Here is the alarms wiring diagram, so my assumption is IM3A, IM3B, or both, aren't connected or improper. But this is all sealed up, with black wiring, and loomed  
    • hardsteppa
      Hi everyone.

      By hardsteppa · Posted

      Ceste, jak se mas Marek...sorry I only have english keyboard. Are you a fan of Poland's greatest band ever?   
×
×
  • Create New...