Jump to content
SAU Community

Recommended Posts

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

have you got a complete stock rb25det with auto trans?

Got 2 RB25DET's

1 is complete minus turbo with flywheel - $1000

1 is complete but a little bashed up with auto trans -$1250

Don't have any coupe 33 side mirrors do you? prefer passenger and white???

Might have one in around the place, will let ya know once everything is sorted out.

any rb25 heads?

No heads but there is a complete schmick RB25DE minus coilpacks and cam gear cover $800

any r34 gtr parts? front guards?

I don't think anyone in Adelaide has R34 GTR parts.

32 gtst sus? coilovers? aftermarket shocks etc?

Theres some aftermarket sus on a pallet, might be something there for a R32.

Got a pair of rear S15 Tiens but condition of these is unknown $400

any coilovers for an s14? long shot...

Got a pair of rear S15 Tiens but condition of these is unknown $400

What have you got left for R32 GTR?

any ABS unit?

Will be in town next week

Nope sorry. Had 2 GTR 1/2 cuts both gone.

Come to think of it if you have any hacked up looms i need some pins off it to wire up my pfc :D

Nah man, sorry.

HEy do you have a R34 GTR gear knob??

Negative

any r33 gtst coilovers or clean/ unscratched headlights?

Got a pair of S15 Tien's, they should fit the R33 but condtion is unkown.

Got a pair of S2 headlights, fog spec, busted brackets - Make an offer if you think they'll be of any use to ya.

  • 1 month later...

This is pretty much whats left besides some motors.

All sorts of bumpers - FC 180SX Silvia Skyline

Theres a bunch of sus components left. I'll take a pic of whats on offer.

Kakimoto cat back for an R33 with light squished middle muffler

SS Kakimoto cat back with de-cat suit R32 GTR / GTST

SS cat back suit early WRX

Aristo cat back Details and photo

Pipe with JunBL cannon

Pair of S14/5 R33 Tien coilovers condish unknown

U13 Bluebird with a SR20DE and 4WD autotrans

RB20DE / R33 RB25DE (MINT!!) / 2 x RB20DET redtop / RB25DET R33 and C34

CA18 Gearboxes

3 x Jetski

MX5 Bommex front bar and sideskirts, in need of lots of TLC

Hatches

2 x 300ZX

FC RX7

FD RX7

2 x 180SX

180SX LHR 1/4

Doors

3 x S13 LHS

1 x S13 RHS

R33 sedan RHS

1 x FD RX7 RHS

2 x FD RX7 LHS

A31 Cefiro RHS D/P & LHR

SW20 RHS & LHS

Bonnets

FC RX7 Non turbs

Z32

2 x R32

Aristo

MX5

GA70 Supra

Fenders

2 x R33 LHS

4 x R33 RHS

2 x S13 RHS

2 x FC RHS

1 x FC LHS

2 x R32 LHS

1 x R32 RHS

180SX rear bumper cut complete

CALL 8240 2088 FOR PRICES

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
×
×
  • Create New...