Jump to content
SAU Community

Recommended Posts

  • Replies 133
  • Created
  • Last Reply

Top Posters In This Topic

Originally posted by zanda

so to ask the question again, any other people willing to tell their tales of horsepower and woe?

...or are we saving that for pas?

Ohhhhh boy Zanda i could tell you a tale about horsepower and woe.. but thats till after PAS.... I'm sure paul can testify that my story about sly should have a movie about it..... after PAS though :-)

Paully,

Used to old turbin and squirted off a 316rwhp @ 12psi(without NOS). We tried 18psi for a couple of run but the graph was shitting and the coil packs begun to break down + (pinging).

So I can do a dyno run at PAS if needed though with the time need to setup car on dyno packs I doubt if you will even have time to get more than two cars on a run. 18psi figures were SWEET

:headshot:

Originally posted by SHUTO-BOY

JUDGED- we need NOs!! hope u run it on the dyno with Nos, comeon mate

I will see if STEVE SST will let me run on his dyno with a 2sec shot just to see some numbers but that will be after PAS as need to keep the cars we have there running and alive.

:ak47:

Originally posted by Steve-SST

This shootout may end up with a few dead cylinders.

Yeah mainly Pauls:D please tell me there not using those dyno pac dynos for auto salon!! can someone confirm or deny this for me?? those wheel changes are so bloody long and frustrating... the crowd will hate it.... dyno shootouts take long enough as is gettin eveything ready as shown in motorvation.... but to also have to take off the wheels is going to show no lack of interest to the crowd when having to wait even longer!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...