Jump to content
SAU Community

Recommended Posts

If the Jun cams are new the info should be on a cam card/sticker on the box. You'll have a degree figure for both the intake and exhaust. Ask your engine builder where they think they should be set but 115btdc and 115atdc will probably get you started. The engine builder should check clearance on them though.

Link to comment
https://www.sau.com.au/forums/topic/247625-jun-rb25-cams/#findComment-4301496
Share on other sites

haha yeah SR's are known to break Rocker Arms on the stock valvetrain. Ive got almost everything upgraded though. Ive hit 10krpm a few times doing burnouts and such with no issues. Engine has over 10k miles of daily driving and daily drag abuse. Its been good for the little engine that could.

Link to comment
https://www.sau.com.au/forums/topic/247625-jun-rb25-cams/#findComment-4301497
Share on other sites

If the Jun cams are new the info should be on a cam card/sticker on the box. You'll have a degree figure for both the intake and exhaust. Ask your engine builder where they think they should be set but 115btdc and 115atdc will probably get you started. The engine builder should check clearance on them though.

thanks for that, i lost the box so though i would ask :P

Link to comment
https://www.sau.com.au/forums/topic/247625-jun-rb25-cams/#findComment-4301629
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For fuelling the Haltechs have O2WB fuel controllers. Very useful for helping tuning VE and correcting for *small* mistakes. Of course if your injector/cam/trigger/sensor data is just wrong (or for a GTT which is not a GT) then you will get impossible reactions to things. I am sure you know this already but the reason people don't typically put haltechs (or any Aftermarket ECU) on GT's is because there's practically no real gains to be had - So this knowledge won't be commonplace.
    • Can someone tell me if the cracks seen in the rear sway bar bushings in these photo's is unacceptable from a roadworthy point of view?  
    • Shouldn't need a "base map" for anything other than guidance to ignition tuning. You just need the engine capacity right, the injector size right, and something, almost anything, for a VE map. On an NA engine, fuelling is almost completely a function of load signal & rpm. It should run and drive with a completely flat fuel map. It will be too lean under load, but that's easily fixed. We used to tune all ECUs without any base map. There were no such things (until someone had tuned a near stock engine on one, and then they had a "base map".
    • What did you actually buy/how much did it cost? When I got mine in like.. 2017...? 2019? the aim was to run Torque for gauges via ODB2 and things like Track Addict/Laptimers/Dashcam/Reversecam/Spotify etc. Mine never broke, but I wonder if you've got the same needs (it sounds like it). Cause I liked the idea of being able to do anything with it. That said, yours also cost 3x the cost of what I spent so... food for thought.  
    • For me there is a massive difference in manufacturer or big brand crippled android (Sony, Kenwood etc) vs the sort of thing I've installed here, which is basically just a tablet in DIN form factor with open Android, and the other model of course is mirroring - Android Auto/Carplay. I hate the locked down manufacturer and AA options where they decide what apps I'm allowed to install, including the Launcher but also importantly things like Ecutek (for this car) or Real Dash (Stagea) are not supported. Plus those crippled versions tend to be slower due to both overheads and lower spec hardware. On the other hand, when this breaks I'll likely be in trouble for support....but how is that different to owning an Infiniti anyway
×
×
  • Create New...