Jump to content
SAU Community

Recommended Posts

As I understand it, the main reason for using a turbo timer on a turbo'd motor is to give the turbo's a little time to spool & cool down before stopping the flow of oil to them.

I personally can't see any reason for a turbo timer on a N/A, except for trying to mislead others into thinking you car is turbo'd!:P

anycar would benefit from a cooling down, but its not as needed in NA cars, i think the Apexi turbo timers (some of them) have TUrbo and NA on their packaging....Rice factor for NA cars.

Turbo cars should cool down because the turbo runs very hot, and oil is needed to extract the heat away. Leaving the car in idle allowes the oil to circulate through the turbo

if your going to put a turbo timer in a n/a , F*uck off the Apexi shit not worth the $$, go to jaycar and get 1 for $20 that u make your self that keeps you car running for 30sec after u turn it off.

personaly it's a rice factor for n/a cars.

but i would do it coz i'm rice

(chicks may think it's cool, i dont know)

haha its ok guys i was never actually considering getting one, waste of money and completely unnecessary. i was just curious if there was a reason for it saying on the package "for turbo and n/a models" - like if there was any benefit in running a non turbo car for a bit after you stop. i usually run it for about 30 sec after i stop just while i grab shit off my back seat, tidy things up a bit etc

anyway thanks for the replies :)

I use my turbo timer to warm up the engine, b4 driving.

Turn the engine on, set timer for 10 min, take keys out, lock doors, go back inside house, get ready to go out, eng. is nice and warm and has suffered the least stress. (most wear and stress on an eng. is caused with-in the first 10 min.) If i take longer to get ready, the eng. turns off, but will still be at full operating temp. by the time i get in the car.

PS: Don't forget to put the key into the ignition b4 putting car into gear. :D

Jimbo2000, i was pretty sure that nos as an oxidising agent, also cools the charge of air as it reacts and then combusts?? therefor the car shouldnt be any hotter? please correct me if im wrong?

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hard to say, just pop the rocker covers off and have a look if you think it's cammed. You probably need to replace the valve cover gasket/half moons anyways.
    • From my youth: GTi-R clutch change is a massive pain. The gearboxes are fragile? But the car is super cool and I want one 😢 
    • Remember this is 1988 tech.
    • Driveline vibration is resolved. I ended up loosening all my engine mount and trans mount bolts, giving it a good shake then retightening everything and it's gone... Let's just say I was surprised that fixed it.  I've been happily driving it around again but unfortunately put zero time into my direct port/constant pressure WMI setup. I'm on vacation next week, so I'll try and finalize it then.  On a different note, I spent all week fuel/ignition mapping 2x 216L V16 engines. Turbo's were burning glycol and we swapped them out for larger units. We also had planned emissions testing on site, so I figured I'd be there the same week to use their instrumentation and massage any emissions issues out if needed. This was a first for me. Fuel management is similar in certain ways to automotive (i.e air density as load variable) but very different in others. It's all PLC based and AFR's are controlled by air and not fuel. They use a control valve between the turbo and air manifold to control pressure which in turn controls AFR's. Due to this, target AFR tables supplied by the OEM are in pressures and not mass which really through me off. They use air pressure vs fuel pressure tables. I also relied on an O2 concentration sensor the emissions team had in the exhaust. Ignition timing was also all over the place and we were losing a fair bit of power. They're now happily sitting at 16-40BTDC depending on load. We were making about 1600kw at 900rpm at 90% load. Engines were running a lot smoother as well.    
    • heh, aint no R32 ever meeting modern targa cage rules unless the driver is veeeery short OP, good luck with the sale, since its already in the land of freedom I'm sure you will find a good buyer.
×
×
  • Create New...