Jump to content
SAU Community

Recommended Posts

Is there anyone new joined?

Me and one of my mates with a ceffy (chris/ anticeptik on ns.com forums) were just talking the other day and we realised we dont know anyone else with a ceffy. I know ryan has one but i havent seen.

So if theres any other guys out there that have freinds with ceffs plz let em know and well organise something

Kim

Edited by Starionturbo
Link to comment
https://www.sau.com.au/forums/topic/248234-melbourne-cefirolaurel-meetupcruise/
Share on other sites

Im down, but i need to do a overhaul, all the arms arnt up to scratch.

Should be good at the start of next year hopefully

Bout time i pulled my figure out and treated her right.

Edited by anticeptik

Yeass i know you works 510 - did u fix ur car up after the little incident with the XF ute?

Ryan fkn register ur car -

DanJ - are u the guy whos house I came to last year and got the GTS-4 skyline parts out of?

Chris thats a weak excuse for a ceffy meetup.

Get permits for the day kents!!!

^ lmao

i'm in the same boat

Ryan i thought u were selling up anyway? if not just take my stuff as stated before

I will sell if someone wants to buy, but still planning on getting RWC, just need to get some time to organise stuff for it. Going to change the turbo to low mount which should help a bit ;)

Will give you a call soon about the parts.

Edited by konect
  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...