Jump to content
SAU Community

Recommended Posts

Has anyone else noticed that the boost drops off from 13 to 10?
You'll also note that the top end is only running 10psi. The boost drop off in the top end is common with standard turbochargers when pushed hard and can be overcome with a better boost controller.

Ahh, yep.

  • Replies 53
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Posted Images

Here is my dyno. Dont stress about the A/f ratio not being there it is fine. The car runs fine its just a comparison. As you can see my boost does the same thing.

If i adjusted the wastegate to open closer to the desired boost level will this spiking shit stop and the bleeding back. At this stage the actuator is set to what ever a stock one it bout 7psi i think and i have a bleed tap doing the rest. The tuner stated that if i stuffed with the actuater getting it to open thus making less work for the bleed tap the boost will be alot smoother.

Any truth behind this

post-23139-1228959828_thumb.jpg

I tuned Dr Doof's car yesterday arvo and he has pretty much the same mods, on 12psi it made 203rwkw

I think the tuner meant if you had a Wolf 3D you would have 400kw... those computers are pretty damn special

I tuned Dr Doof's car yesterday arvo and he has pretty much the same mods, on 12psi it made 203rwkw

I think the tuner meant if you had a Wolf 3D you would have 400kw... those computers are pretty damn special

just like 'special' people have to attend a 'special school'

GREAT! coffee on the bloody keyboard now and people at work looking at me funny!

hahahaha this has happened to me before :P

HAPPY BIRTHDAY MISTA DART!

ohhh Mr Dirt's Birthday! Happy Birthday matey!

Did you guys know that Mr Dirt is a famous movie star ?

hahahaha this has happened to me before :(

ohhh Mr Dirt's Birthday! Happy Birthday matey!

Did you guys know that Mr Dirt is a famous movie star ?

yeah visit www.uglygirleatingsmallcock.com and go to the vids section

I tuned Dr Doof's car yesterday arvo and he has pretty much the same mods, on 12psi it made 203rwkw

I think the tuner meant if you had a Wolf 3D you would have 400kw... those computers are pretty damn special

Yeah I was gunna mention that... the mods are staggeringly close!

Also, that allen key wasn't mine, I have 2 now... so I stole one from UAS :(

Happy Birthday Dr DiRT! (just incase a bday thread doesn't pop up :/)

Yeah I was gunna mention that... the mods are staggeringly close!

Also, that allen key wasn't mine, I have 2 now... so I stole one from UAS :(

Happy Birthday Dr DiRT! (just incase a bday thread doesn't pop up :/)

can you give it back to him please?

BAH! Take it up with a frickin moderator.

a real moderator ? or a smart ass who edits your posts? :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
    • Trailer prep is underway... Lined up the wheel to get a rough indication of how it would sit Then removed all the bits (as far as possible) and gave the frame a light sand and quick lick of paint   Then added some carpet
    • okay, so I figured this out, removed needles and reinstalled after swapping the gauge face on my triple gauge for my ER34, all work and look good. I tried to do the same for the main cluster, but the main cluster gauge faces are dished, the replacement gauge face are flat, so due to the dish in the org face ,mounting backing plate (clear) and depth of the needle, the flat gauge face will not work. I notice that R34 gtr gauges are flat, appears to be different clear backing plate that aren't dished. are these available, or what have others done to install flat gauge faces?
    • Cheers mate. Seems some people get lucky others don't. It looks like the motor was detonating (to be expected if it was overboosting I suppose) as the pistons had a lot of detonation damage, and the bearings were stuffed. The bores were very scoured too, not sure if that's from the pistons or bits of ceramic turbo. By the by now. Have been trying to avoid the rabbit hole too much on the rebuild, and there's been a few hurdles along the way, but with any luck I'll have the car back soon™. Might even pop up a thread then.  
×
×
  • Create New...