Jump to content
SAU Community

Recommended Posts

PRICE DROP

rb25det complete engine 110,000kms with all accessories, loom and computer. Compression tested a couple of days ago and was 150-160psi across all cylinders

$1500

5 speed manual complete with shifter, sensors, slave cylinder, clutch fork and thrust bearing. Was rebuilt by previous owner and has only had around 6 months driving on it since, feels perfect when driving.

$1600

or full manual setup minus gearstick surround for $1900

or both engine and box together, $2900

full brake setup with hubs, brake lines and handbrake stuff

$1000

tail lights, $50each or $100 for both with skyline centre garnsh

rhs guard with indicator, straight with a couple of small scratches, $50

rear bumper with reo bar, perfect condish, $100

boot with wing, boot is perfect, wing needs a bit of fibreglass work to the passengers side, $100

set of stock shocks with lowered springs, rides fine so assume they are all in good condition, $150

drivers headlight, has slight damage, $40

thats just a couple of things i felt like listing, still pretty much everything else in the pics is for sale, negotiable on most prices

  • Replies 64
  • Created
  • Last Reply

Top Posters In This Topic

Hey mate...just wondering if you have the original trim inside of the boot (floor and walls) and would be interested in selling...? If so can ya get us a pic and price to post to brisbane.

Cheers

Brendan

Hey mate...just wondering if you have the original trim inside of the boot (floor and walls) and would be interested in selling...? If so can ya get us a pic and price to post to brisbane.

Cheers

Brendan

yeah the trims are all there but im pretty sure most of the wall ones are broken, will get pics and you can decide if you want them

-deleted-

There is something i need but i don't think you'll be shipping outta Australia hence i've deleted the reply.

Edited by teng

hey mate can u send me some pics of the exhaust please. and also how much do u want for the rad support? pm me with a price for everything to please.. rad support, exhaust and condensor.

cheers

dean

Hey mate would you be willing to part with whole drivers door (including mirror), and front right qtr panel if they are in good nick?

If so how much would you want for them? Please PM me

Cheers,

Karl

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
    • Well this shows me the fuel pump relay is inside the base of the drivers A Pillar, and goes into the main power wire, and it connects to the ignition. The alarm is.... in the base of the drivers A Pillar. The issue is that I'm not getting 12v to the pump at ignition which tells me that relay isn't being triggered. AVS told me the immobiliser should be open until the ignition is active. So once ignition is active, the immobiliser relay should be telling that fuel pump relay to close which completes the circuit. But I'm not getting voltage at the relay in the rear triggered by the ECU, which leaves me back at the same assumption that that relay was never connected into the immobiliser. This is what I'm trying to verify, that my assumption is the most likely scenario and I'll go back to the alarm tech yet again that he needs to fix his work.      Here is the alarms wiring diagram, so my assumption is IM3A, IM3B, or both, aren't connected or improper. But this is all sealed up, with black wiring, and loomed  
×
×
  • Create New...