Jump to content
SAU Community

Tensioner Pulley Fouling Belt Cover Rb30/rb26

leeroy_25

By leeroy_25,
in Engines & Forced Induction

 Share

Recommended Posts

leeroy_25 Community Regular

leeroy_25

Posted
Posted (edited)

Has anyone had any isues with the tensioner pulley or belt rubbing on the cam gear cover or lower belt cover going from the 30 build manual? It suggests mocking it up but that would be a lot easier said than done. I gather the general opinion seems to be setting the pulley out a further 1mm than the manual suggests so you get more movement on the tensioner.

Any info please..

Edited by leeroy_25
psi Experienced

psi

Posted
Posted

I have been looking at this issue. I was going to ask the same question. Do you guys bother trying to 'cover' the idler, or just leave it hanging in free air? how does the belt go with road grime and stuff?

cheers

leeroy_25 Community Regular

leeroy_25

Posted
  • Author
Posted

Thanks All!

Hole is in my block now so fingers crossed! I have looked at some other blocks and some seem to have some very different hole positions.. I am guessing it's not really thqt critical within reason as the tensioner has a fair bit of adjustment.

Hey Al, Nice looking motor! Looking at you turbo oil feed line (unless it's the water one?).. Are you running a series 1 block by any chance? If so would be interested to see what you did about oil and water feeds? I was planning on getting my oil feed from the pressure switch. and draining to the sump.. water is easy enough to put in where it belongs!

Any more pic of your build?

Cheers

Lee

Al Grand Master

Al

Posted
Posted

psi: The plate is only held in by two existing bolts, so it's really easy/quick to take off. Not sure why you would need/want a hole for adjustment anyway; once the belt is fitted and properly tensioned you wouldn't need to adjust it again.

Thanks All!

Hole is in my block now so fingers crossed! I have looked at some other blocks and some seem to have some very different hole positions.. I am guessing it's not really thqt critical within reason as the tensioner has a fair bit of adjustment.

Hey Al, Nice looking motor! Looking at you turbo oil feed line (unless it's the water one?).. Are you running a series 1 block by any chance? If so would be interested to see what you did about oil and water feeds? I was planning on getting my oil feed from the pressure switch. and draining to the sump.. water is easy enough to put in where it belongs!

Any more pic of your build?

Cheers

Lee

Thanks Lee.

Pretty sure it's a S2 motor.

Few more angles of the engine on the stand, not sure if you wanted to see any other pics; like the pistons, head porting, engine bay prep and completed engine bay, etc.

post-1811-1229783590_thumb.jpg

post-1811-1229783712_thumb.jpg

post-1811-1229784255_thumb.jpg

leeroy_25 Community Regular

leeroy_25

Posted
  • Author
Posted

Nice pics!!

That does nicely thank you! What's the external oil filter housing part in the third pic?? Is that for an external pump or something?

What spec you got and what power are you hoping to get?

Cheers

Lee

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GoHashiriya
      From Japan and back to Europe, my sh*tbox R34 GTT

      By GoHashiriya · Posted

      Cheers. Skyline is back on the menu, can’t get rid of it. It’s like a child you don’t want, or herpes 
    • Dose Pipe Sutututu
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Dose Pipe Sutututu · Posted

      Welcome back brother 
    • GoHashiriya
      From Japan and back to Europe, my sh*tbox R34 GTT

      By GoHashiriya · Posted

      I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • GoHashiriya
      From Japan and back to Europe, my sh*tbox R34 GTT

      By GoHashiriya · Posted

      It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
×
×
  • Create New...