Jump to content
SAU Community

Tensioner Pulley Fouling Belt Cover Rb30/rb26

leeroy_25

By leeroy_25,
in Engines & Forced Induction

 Share

Recommended Posts

leeroy_25 Community Regular

leeroy_25

Posted
Posted (edited)

Has anyone had any isues with the tensioner pulley or belt rubbing on the cam gear cover or lower belt cover going from the 30 build manual? It suggests mocking it up but that would be a lot easier said than done. I gather the general opinion seems to be setting the pulley out a further 1mm than the manual suggests so you get more movement on the tensioner.

Any info please..

Edited by leeroy_25
psi Experienced

psi

Posted
Posted

I have been looking at this issue. I was going to ask the same question. Do you guys bother trying to 'cover' the idler, or just leave it hanging in free air? how does the belt go with road grime and stuff?

cheers

leeroy_25 Community Regular

leeroy_25

Posted
  • Author
Posted

Thanks All!

Hole is in my block now so fingers crossed! I have looked at some other blocks and some seem to have some very different hole positions.. I am guessing it's not really thqt critical within reason as the tensioner has a fair bit of adjustment.

Hey Al, Nice looking motor! Looking at you turbo oil feed line (unless it's the water one?).. Are you running a series 1 block by any chance? If so would be interested to see what you did about oil and water feeds? I was planning on getting my oil feed from the pressure switch. and draining to the sump.. water is easy enough to put in where it belongs!

Any more pic of your build?

Cheers

Lee

Al Grand Master

Al

Posted
Posted

psi: The plate is only held in by two existing bolts, so it's really easy/quick to take off. Not sure why you would need/want a hole for adjustment anyway; once the belt is fitted and properly tensioned you wouldn't need to adjust it again.

Thanks All!

Hole is in my block now so fingers crossed! I have looked at some other blocks and some seem to have some very different hole positions.. I am guessing it's not really thqt critical within reason as the tensioner has a fair bit of adjustment.

Hey Al, Nice looking motor! Looking at you turbo oil feed line (unless it's the water one?).. Are you running a series 1 block by any chance? If so would be interested to see what you did about oil and water feeds? I was planning on getting my oil feed from the pressure switch. and draining to the sump.. water is easy enough to put in where it belongs!

Any more pic of your build?

Cheers

Lee

Thanks Lee.

Pretty sure it's a S2 motor.

Few more angles of the engine on the stand, not sure if you wanted to see any other pics; like the pistons, head porting, engine bay prep and completed engine bay, etc.

post-1811-1229783590_thumb.jpg

post-1811-1229783712_thumb.jpg

post-1811-1229784255_thumb.jpg

leeroy_25 Community Regular

leeroy_25

Posted
  • Author
Posted

Nice pics!!

That does nicely thank you! What's the external oil filter housing part in the third pic?? Is that for an external pump or something?

What spec you got and what power are you hoping to get?

Cheers

Lee

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • JC71
      new 1.5 LSD issues/concerns

      By JC71 · Posted

      sold listed as a Tomei LSD 1.5 Way For 1998+ Nissan Skyline ER34 25GT RB25DE w/Open R200 https://www.ebay.com/itm/174006114594?campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=&mkrid=711-53200-19255-0&loc_physical_ms=108689&loc_interest_ms=&campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=71883f2ccc571356e0a757bc7adfdde2&mkrid=710-53481-19255-0&loc_physical_ms=108689&loc_interest_ms= it went in like butter all gears, alignment, back lash etc, rotation and clearances correct, and if rolling all rotates smooth and free when coasting down road , clutch in or out over 10 mph smooth... its the binding, clunking and jerking from a stop that is most concerning, also seems like its going to tear the tires off in 10 miles of normal road driving. 
    • Kinkstaah
      new 1.5 LSD issues/concerns

      By Kinkstaah · Posted

      What 1.5 way? There's no such thing really as a 1.5 way, just different ways of explaining 2 ways with different ramp rates. HOWEVER. In any driving in a straight line your 1.5 or 2 or 1.7 way should have no clunking at all. With the clutch fully depressed the diff should be silent (unless it's welded but I'm assuming it's not). Something aint right here.
    • JC71
      new 1.5 LSD issues/concerns

      By JC71 · Posted

      Clutch is a spec brand, new clutch system,( PP, flywheel, friction disc, etc. pull type) installed 100 miles ago, with no problems.
    • JC71
      new 1.5 LSD issues/concerns

      By JC71 · Posted

      looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drove beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Matt Z
      SAU NSW - Archies Flame Grille Meet & Cruise to Kurnell

      By Matt Z · Posted

      Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
×
×
  • Create New...