Jump to content
SAU Community

Recommended Posts

Oil is like PS3 games, every1 has a favourite, How I chose was to read as much as I could from testers, and looked at what race teams in Japan were using too.

As long as the oil is fully synthetic, you should be ok.

Just for the record I use Motul 8100 5W 40

Live on Gold Coast, temp gets to nearly 40 in summer and 0 in winter as I live in a valley. Its good stuff, bit pricey but worth it.

Just make sure Oil & Filter are changed every 5000k's-thats the true secret

Link to comment
https://www.sau.com.au/forums/topic/249390-what-oil/#findComment-4325378
Share on other sites

i use motul 300v. :D

Dude you're rich :D

Motul 8100 5W40 here.

mines coming up soon too.. so I need to know what oil and oil filter to buy (stock engine ~ 50,000km)

You need 145A oil filter if your car was manufactured before 11/98. If you was after that you need Z442. They're both thread compatible but the Z442 is smaller and has finer filtration.

Link to comment
https://www.sau.com.au/forums/topic/249390-what-oil/#findComment-4331101
Share on other sites

if your car hasnt been run on fully synthetic for the last 100000kms or something along those lines, going fully synthetic wont really make too much of a difference now. Remember when half of these cars came out, fully synthetic oil wasnt out yet. I use castrol 5-30 fully synthetic which works for me, but every car is different and wether your engine is worked or not.

Link to comment
https://www.sau.com.au/forums/topic/249390-what-oil/#findComment-4331837
Share on other sites

I was reading something in Import Tuner magazine, talking about how this really popular engine building in the states looks after his race cars and his daily driver (a camaro). He was saying that shell full synthetic removes about 60% deposits from old motors in the first oil change. So it definately makes a difference even if you haven't run synthetic for it's entire engine life.

Link to comment
https://www.sau.com.au/forums/topic/249390-what-oil/#findComment-4331906
Share on other sites

ouchies,

well in my R33 GST-T i used,

Semi-synthetic Oils 'cause its a waste to throw hundreds in when your dumping it out every 5thou kms'

7.5/30 winter 'cooler weather, so wont loose its velocity as bad as summer

10/40 summer 'cause oil will be hotter, so need something that will maintain itself'

personally i found 7.5/30 too noisey in summer... because its so thin and is like piss water when hot...

and considering its an older car/engine (km's)... if its to thin it can get past the oil ring n you burn a little, not that you should notice it.

Link to comment
https://www.sau.com.au/forums/topic/249390-what-oil/#findComment-4333353
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The alloy coolant reservoir has a sight glass, so as long as I can see coolant in the sight glass it's GTG, as for PS, it isn't anything catastrophic if it gets low, and as it hasn't lost a drop since I have owned the car I cannot see it being an issue, even after putting the "big block" 2.5 in....LOL The only time it gets slightly messy is at oil changes, as the oil filter sits above the frame, and I need to use a plastic bottle with its bottom cut off to catch the flow when loosening the filter
    • Good on you for taking on the job, but it is a big one. Even if you have bolt on manifold and turbo, you will need: Post throttle pressure source to boost controller to wastegate (and FPR, and ECU/MAP sensor) Pre throttle pressure source to top of BOV(s) Oil feed - you can take that from the standard port in the middle of the block Oil return to block under the turbo - this is much trickier than it seems to route a decent/wide pipe past the manifold. You really can't use rubber hose because it is way too hot there, and also the oil out of the turbo core is a bit frothy so it needs to have a decent diameter Water feed - you can take that from the standard port in the rear of the block. Water return - mine runs to a T into the heater box return, just make sure you don't create a high point making bleeding hard. All of those lines should use 200 series style teflon braided hose with heat shielding because everything needs to be routed past the manifold. Also a turbo beanie is a really good idea to minimise the chance of the car catching fire (under bonnet lining in particular) You also need to decide a cam cover breathing solution as well, will you vent externally via a catch can (probably illegal) or return to the intake (plumbing required and can oil up everything over time) Keep in mind the intake and exhaust piping in the engine bay will be custom so you either need to be able to fab ally and steel or have someone you can get a car that isn't running to. Get the wideband fitting welded into the dump pipe at the same time. Also, just my opinion, a screamer pipe attracts attention and doesn't add power, I'd plumb it back if you want to be allowed to keep the car on the road. BTW do you know anything about how healthy the motor is, and what power you are targeting? Doubling or tripling the factory power on an unknown motor is a little risky. Also fuel system will need some attention (pumps, high current hanger, direct power and earth feed, injectors etc)
    • Wrinkle black will be a thing for both
    • As I wait for parts to be delivered, I have managed to procure via a contact a R32 Nistune ECU......for now I just want to monitor what the car is doing but eventually.......who knows where we go 😂
    • To back this up, I'm always looking on the outside, seeing the level, and then opening it up anyway, as I'm worried the level I've looked at, is more so a scunge line. Then you end up dipping your damn finger in it too depending on the type of tank you're looking at just to make sure I'm not going insane.   PS, Mark, polish up the none moroso one a bit and then give it a clear coat. The Moroso one looks to be way shiner (not mirror polished, just shinier) and it'll still look weird with the two different alloys beside each other. Either that, or Id probably paint them a flat black...
×
×
  • Create New...