Jump to content
SAU Community

Recommended Posts

I have made the decision to sell off my R32 GTR

The car does not get used much anymore and the rego is just running out without being used. With another dedicated racecar nearing completion it will be used even less next year.

The base car is a 90 model R32 GTR Originaly gunmetal grey.

Engine mods

Engine was rebuilt 2,500Km's ago.

New R33 crank shaft

- Standard bearing sizes

- Fully balanced with clutch and harmonic balancer fitted

- Grub screwed oil galleries

- Modified oil galleries (specific details available to purchaser)

Original 05u block

- Was cleaned, sonic tested, tunnel aligned and honed.

- Internal modifications to assist oil return to sump (specifics available again)

- Enlarged oil return galleries from head to sump

- Oil restrictor fitted

- Modified coolant passages

Factory R33 N1 rods

- Were from an unstarted crate engine

- Fitted with new ARP rod studs and nuts.

Factory N1 pistons

- Were all equally weighed (specific weights to purchaser)

- Fitted with new rings

- From same engine as the rods

Original Head

- Cleaned, decked valves cut and guides replaced

- New stem seals and all spring seat pressures set

- After market Graphite head gasket

- JJR adjustable cam gears and Clear cover

- Mild port work was done to the head when it was apart, nothing major but some casting irreglarities were cleaned up and was flow benched to ensure everything was even and equal.

Turbos are believed to be steel wheel direct replacements

Has an intank 040 pump fitted

Basicaly the engine was blueprinted and assembled, so squish heights etc were all checked, and machined to acheive tolerances required. Its using the same clearances as our race engines but without the exotic pistons/rods/crank etc.

The builder is more than happy to put purchasers in contact with the machinist who did all the pre assembly work to verify exactly whats in it and how it was built.

2x 3/4 inch custom made front pipes (formerly made for the race car)

90mm exhaust from cat back

Extreme heavy duty button clutch

Nismo Slave cylinder

Transfer case was repaired/overhauled 1000Km's ago

Blitz ID3 boost controller

Custom oil catch can system

Suspension- Apexi shocks and Eibach Springs

- Nismo lower rear control arms

- Nismo upper rear control arms

- Nismo Front castor rods

- Cusco upper front camber arms

- Replaced sway bar bushes and links

Its currently set-up with spring rates to suit semi slicks and does handle very nicely on the track.

The body was resprayed last year in a brilliant white. Inside and out paint job done by exclusive colours. Has a N1 rear boot lip and bonnet lip fitted.

Paint work is still immaculate

Comes with Enkei 17 by 9.5 inch rims with decent tires.

Brakes - Callipers were all overhauled with new genuine nissan seals at the beginning of 2008.

- DBA 4000 series slotted front rotors

- Unknown slotted rear rotors

- Bendix ultimate rear pads

- TRW lucas front pads

- Master cylinder recently had new seals fitted as well (mid 2008)

The interior is all in great condition but the seats have the usual bolstering wear on them.

Car recently competed in the NSW dutton rally and held its own very well without missing a beat.

Its completed in club level super sprint championship in 2008 as well as many a track days.

With a good driver it has achieved - wakefield park 1.08.20

- oran park south 49.45

- oran park GP 1.20.10

All of which were done on average Advan A048 tires.

I'm asking $20,000 for it and not open to any form of trade.

May be negotiable if it's going to a good home.

Located in Sydney

Contact 0404 832 620 After 5:30pm weekdays

Here are a few photos of it, I can provide interior and engine bay photos if serious interest is had as the car is currently in storage.

post-8051-1229597160_thumb.jpg

post-8051-1229597122_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/249424-r32-gtr-white-with-mods/
Share on other sites

It has a Apexi Power Fc

On road has never been over 1bar boost and about 280kws at the wheels

Eibach springs I can run different combos but currently it has 8 fronts and 6.5 at rears.

If you want anymore info or photos give me a call :banana:

Contact Jess or Brad 0404 832 620 After 5:30pm

I have made the decision to sell off my R32 GTR

The car does not get used much anymore and the rego is just running out without being used. With another dedicated racecar nearing completion it will be used even less next year.

The base car is a 90 model R32 GTR Originaly gunmetal grey.

Engine mods

Engine was rebuilt 2,500Km's ago.

New R33 crank shaft

- Standard bearing sizes

- Fully balanced with clutch and harmonic balancer fitted

- Grub screwed oil galleries

- Modified oil galleries (specific details available to purchaser)

Original 05u block

- Was cleaned, sonic tested, tunnel aligned and honed.

- Internal modifications to assist oil return to sump (specifics available again)

- Enlarged oil return galleries from head to sump

- Oil restrictor fitted

- Modified coolant passages

Factory R33 N1 rods

- Were from an unstarted crate engine

- Fitted with new ARP rod studs and nuts.

Factory N1 pistons

- Were all equally weighed (specific weights to purchaser)

- Fitted with new rings

- From same engine as the rods

Original Head

- Cleaned, decked valves cut and guides replaced

- New stem seals and all spring seat pressures set

- After market Graphite head gasket

- JJR adjustable cam gears and Clear cover

- Mild port work was done to the head when it was apart, nothing major but some casting irreglarities were cleaned up and was flow benched to ensure everything was even and equal.

Turbos are believed to be steel wheel direct replacements

Has an intank 040 pump fitted

Basicaly the engine was blueprinted and assembled, so squish heights etc were all checked, and machined to acheive tolerances required. Its using the same clearances as our race engines but without the exotic pistons/rods/crank etc.

The builder is more than happy to put purchasers in contact with the machinist who did all the pre assembly work to verify exactly whats in it and how it was built.

2x 3/4 inch custom made front pipes (formerly made for the race car)

90mm exhaust from cat back

Extreme heavy duty button clutch

Nismo Slave cylinder

Transfer case was repaired/overhauled 1000Km's ago

Blitz ID3 boost controller

Custom oil catch can system

Suspension- Apexi shocks and Eibach Springs

- Nismo lower rear control arms

- Nismo upper rear control arms

- Nismo Front castor rods

- Cusco upper front camber arms

- Replaced sway bar bushes and links

Its currently set-up with spring rates to suit semi slicks and does handle very nicely on the track.

The body was resprayed last year in a brilliant white. Inside and out paint job done by exclusive colours. Has a N1 rear boot lip and bonnet lip fitted.

Paint work is still immaculate

Comes with Enkei 17 by 9.5 inch rims with decent tires.

Brakes - Callipers were all overhauled with new genuine nissan seals at the beginning of 2008.

- DBA 4000 series slotted front rotors

- Unknown slotted rear rotors

- Bendix ultimate rear pads

- TRW lucas front pads

- Master cylinder recently had new seals fitted as well (mid 2008)

The interior is all in great condition but the seats have the usual bolstering wear on them.

Car recently competed in the NSW dutton rally and held its own very well without missing a beat.

Its completed in club level super sprint championship in 2008 as well as many a track days.

With a good driver it has achieved - wakefield park 1.08.20

- oran park south 49.45

- oran park GP 1.20.10

All of which were done on average Advan A048 tires.

I'm asking $20,000 for it and not open to any form of trade.

May be negotiable if it's going to a good home.

Located in Sydney

Contact 0404 832 620 After 5:30pm weekdays

Here are a few photos of it, I can provide interior and engine bay photos if serious interest is had as the car is currently in storage.

post-8051-1229597160_thumb.jpg

post-8051-1229597122_thumb.jpg

Hi how are you? I saw this Gtr the other night and i sent you a text message the other day but i got no reply... I am wondering is this car still for sale? Could u send some pics of the interior if possible to [email protected]

Thanks :)

Hi how are you? I saw this Gtr the other night and i sent you a text message the other day but i got no reply... I am wondering is this car still for sale? Could u send some pics of the interior if possible to [email protected]

Thanks :D

Sorry I dont have any pictures of the interior currently and the car is in storage.

Only interested in serious buyers if your genuine buyer wouldn't you prefer to organise an inspection?

If i had the cash i would buy it off you right now Jess.

Good luck with the sale. Thinks about selling the 34!!!

Aww and I would sell it to you cause I know it would be going to a good home!!

Cheers..I think you need a change like me :cool:

Sorry I dont have any pictures of the interior currently and the car is in storage.

Only interested in serious buyers if your genuine buyer wouldn't you prefer to organise an inspection?

Oh ok thats cool i am genuinely interested in the car and would love to see the car its just i work 6 days a week and its hard for me to get a bit of time to myself hence why i asked if u had any interior pictures...

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
    • When you pulled it off, there is no signs of blown head gasket? Is it possible you have some other issues going on? Possible cracked blocked? Or do you think it's straight up lifting the head? Did you check what the head was torqued to before pulling it down (To see if possibly they're stretching, or starting to break threads out etc)?
    • Seems like a decent result for a modded JZX110. They are bulky in comparison to the 100 and 90 models (which I'd prefer myself) but they are getting very few and far between here in JP these days. Thanks for the detailed review and the import process into the UK. I also have a car which I'm hoping to export from Japan at some stage so it's good to know if someone from the UK was interested in it. By the way the corrosion underneath is par for the course for cars which were located in/near the mountains or along the Japan sea coastline. They get huge amounts of snow every winter and the sodium chloride is used on the roads. Many cars have some kind of rubber like treatment underneath but they tend to limit it to the wheel arches underbody and fuel tank. Suspension arms and sub-frames will have similar corrosion to your JZX110 which is a common sight. See it all the time and car dealers here generally don't even mention it unless asked.
    • If the sound goes away when you clutch in, the 1.5/2 way diffs are just shit, and you are a normal person. The diff is likely "fine" but driving at anything under 30kmh is a violent horrible experience. It would be exaggerated with solid diff bushings and subframe bushings if you have those.
×
×
  • Create New...