Jump to content
SAU Community

R32 Gtr Running Hot After Coolant Change

black sky

By black sky,
in Engines & Forced Induction

 Share

Recommended Posts

black sky Rising Star

black sky

Posted
Posted (edited)

Hi Guy's

I changed my coolant since the old water was rusty as sh!t. i put in the coolant stuff blead the system and now the temp when driving sits at over 90 on my power fc. The needle doesn't go up above half way on the dash but still it makes me worried.

What's the proper way to blead the gtr coolant lines and is there something else i need to do??

and also my heater is no where near as hot as it usually is when i have it on 32 degrees

any help would be great

Edited by black sky
black sky Rising Star

black sky

Posted
  • Author
Posted (edited)

when i did the change i forgot to put the heater on, but now i've blead it for ages and it still overheats. is there only the one blead point on the GTR??

so should i just keep bleading it???

and the heater isn't working at all even with the engine at 95 degrees it still blows cold air.

cheers anthony

Make sure you have the heater on while you are doing the bleeding....helps get all the air out of the heater core. Sounds like thats where you went wrong.
Edited by black sky

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • soviet_merlin
      WGNC34 - floor mats

      By soviet_merlin · Posted

      Checked with amayama and nope, the full S2 manual set is not available anymore. Unsurprising, but still disappointing as the ? on availability gave a glimmer of hope.
    • joshuaho96
      Tomei gasket

      By joshuaho96 · Posted

      I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Marek
      Hi everyone.

      By Marek · Posted

      Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
×
×
  • Create New...