Jump to content
SAU Community

Recommended Posts

So for my birthday my parents bought me a couple model cars (R32 GTR and a 2005 WRX), i think i remember someone saying they got a Stagea from Stanbridges (over here in perth) but im not sure if it was on these forums pretty sure it was though. I was just wondering if anyone has one where did they get it from? Prefer to buy from a store in Australia but so far can only really find ones in Japan.

Any help would be greatly appreciated.

Thanks,

Corey

Link to comment
https://www.sau.com.au/forums/topic/249695-stagea-model-cars/
Share on other sites

So for my birthday my parents bought me a couple model cars (R32 GTR and a 2005 WRX), i think i remember someone saying they got a Stagea from Stanbridges (over here in perth) but im not sure if it was on these forums pretty sure it was though. I was just wondering if anyone has one where did they get it from? Prefer to buy from a store in Australia but so far can only really find ones in Japan.

Any help would be greatly appreciated.

Thanks,

Corey

Ive got 4 models, bought them all from ebay. 1 mines 260rs, 1 fire department squad car, 1 rs4v and the rare one the dolphin 260rs which i dont think they make anymore. Your best bet is ebay but the the postage is pretty dear. Do a worldwide search and they should come up but be quick as i think theres only limited numbers left. They are good quality models.

Good luck

Stu

My old man got me this for a bday gift, he got it off ebay but didn't say how much he payed, and knowing my old man it wouldn't have been much.

The maker is FUJIMI, and is 1/24 scale, haven't built yet and doubt i will.

post-34938-1229944301_thumb.jpg

My old man got me this for a bday gift, he got it off ebay but didn't say how much he payed, and knowing my old man it wouldn't have been much.

The maker is FUJIMI, and is 1/24 scale, haven't built yet and doubt i will.

post-34938-1229944301_thumb.jpg

Id give you $50 for it if you wanted to sell it :banana:

Cheers

I literally just got that Fujimi kit in the mail from a Hong Kong based store on eBay. I am so looking forward to putting it together!!!!!

I'm taking my bigger stag out of town for a few days to go and stay with family in Geraldine, so I'll have a few days to get started on it.

..and it cost me $NZ60

Edited by mr_infamy
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...