Jump to content
SAU Community

Recommended Posts

Hey Guys,

I am looking at getting a new viper alarm installed in the new year but also want a turbo timer that will work with it. I want to be able to give the installer everything so he doesn't have to wait for anything.

I am partial to the HKS range of turbo timers only because I have had one previously but can anyone tell me what ones I can look at that will intergrate properly.

Cheers

troy,

in short none of them do. adding one to a DEI unit is a major pain. especially if its going on your purple thing :happy:

flick me a PM and I'll explain.

Hey mate,

i actually sell vipers and as the previous person said. it's a pain which is true. it's actually advised that you dont add an aftermarket turbo timer to your viper and just use their inbuilt turbo timer. less headaches.. does exactly the same thing. you can adjust it in 5second increments if i remeber right.

  • 1 month later...

Here's how I fixed this issue:

The guys that installed my alarm told me that the yellow wire on the (viper) alarm harness was what sensed if the engine was running or not. They suggested to cut this wire, but after I did, the alarm thought the engine was never on, so it would start arming while I was driving. Obviously this wasn't a practical solution... So I busted out my voltmeter. What I found was that the yellow wire has 14V running through it when the engine is on, and 0 when the engine is off. I needed to find something that was 14V when the engine is on, and 0 when the key is removed and hook that up to the yellow wire input of the alarm. I tested the wires in the TT harness, but they didn't change when the key was removed, only when the engine turned off. Then somehow my eyes rested on the parking brake wire...

Testing showed that the parking brake wire was 0 when it was pulled up, and 14V when it was released. If I hooked that up to the yellow wire of the alarm, when the parking brake was pulled, the alarm would think the engine had been turned off, and would activate as soon as you opened and closed the doors (I have auto-lock and auto-activate on).

So I ran a wire from the gray wire of the parking brake sensor to the yellow input of the alarm, and it works perfectly, assuming of course that you pull the hand brake every time you get out of your car... The best thing was that the wires I tapped into were in the alarm harness and the TT harness so I didn't have to touch any factory wiring...

Hope this helps...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That's not a transistor --- it's marked ZD1 which makes it a zener diode. As to what the breakdown voltage is, not enough there to divine.
    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
×
×
  • Create New...