Jump to content
SAU Community

Recommended Posts

hey guys and girls that have a 32 could they please tell me/take a pic of what is written on your wheel and tyre plark, you know the badge that has the rim size and tyre size that is prob on the driver side door,

thanks

also where would i find a high level stop light

how do i get proof that says that my car doesnt come with a air bag, i dont think they will do the hard work in calling nissan

are oil coolers and oil relocation alloud

also my bride seats, how do i prove that they are adr approved, well i guess they are as they recline, use orginal mounting

thanks

Edited by Flash89
Link to comment
https://www.sau.com.au/forums/topic/251148-some-help-i-need-to-get-yellow-off/
Share on other sites

Tyre plark you can get from Nissan.

If they said you can't have the oil relocator/cooler then take it off.

High level stop light you can get from autoone or superchump. 'Narva' make them, they aren't pretty but they work.

your seats should have come with a certificate or something.

If they are picking on seats that recline and use original mountings then take the car to another inspector. Supercheap is your friend for the light and tyre sticker you could prob get at any engineer, Phil's mechanical Services is good and hes pretty laid back, prob be able to give you some good advice

both my 32's came with headvisor that had a Airbag warning, neither of them actually had airbags. Airbag light will flash when you start it if it used to have air bags also look in the fuse box to see if there is a fuse of some sort. airbags in 32's are rare as.

what size wheels are you running? I used to have 205 55 16s and 215 55 16s, if u have 15's u should run a 205 65 15 (comodore and falcon spec) but legally you are aloud 2 rim sizes larger from factory. I havnt seen a 15 on a skyline before tho, 16's are the smallest i seen, cos the space saver is sized and profiled to meet a 16" with 205 55 height, but ul be able to get a sticker from nissan if u provide a chassis number, there not expensive, like 15 bucks abouts id say, prob ex japan tho but u never no. Call northside nissan.

Edited by BANGN
both my 32's came with headvisor that had a Airbag warning, neither of them actually had airbags. Airbag light will flash when you start it if it used to have air bags also look in the fuse box to see if there is a fuse of some sort. airbags in 32's are rare as.

what size wheels are you running? I used to have 205 55 16s and 215 55 16s, if u have 15's u should run a 205 65 15 (comodore and falcon spec) but legally you are aloud 2 rim sizes larger from factory. I havnt seen a 15 on a skyline before tho, 16's are the smallest i seen, cos the space saver is sized and profiled to meet a 16" with 205 55 height, but ul be able to get a sticker from nissan if u provide a chassis number, there not expensive, like 15 bucks abouts id say, prob ex japan tho but u never no. Call northside nissan.

I got told when I took my Z over the pit that they were moving to the rolling diameter rule instead of the old 2 inches thing. Maybe something to check up on.

Edited by monk_13
  • 2 weeks later...

could someone please just take a pic of their sticker that they have on their 32 gts-t. went through nissan, and its pretty much just a sticker and its got to come from japan going to take 3-4 weeks and cost me 7.95 hehe

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Try looking at Eibacb/H&R springs Thats what Gary sourced for mine.
    • Hey y'all! I'm curious about how y'all go about widebodying your cars. I noticed that when running a square setup, my front wheels are a bit more tucked in than my rear wheels. Not by much, maybe 5-10mm. This leads me to wonder - when I widebody, should I use narrower front flares and wider rear flares? I found a set of 40mm rear flares that I really like, and was thinking of pairing them with some 18mm front flares, but I don't want the car to look strange. How have others done this? Note, I'm in a sedan. Thanks!
    • And if it was anything other than an auto tranny part, it might be a problem. But seeing as all auto trannies belong in the recycling bin, it's fine.
    • I have an R32 Fenix rad. It is good.
    • All the schemas I can see, indicate your typical setup of ATF 'cooler' (read: heat exchanger) in the bottom radiator tank..ie; https://nissan.epc-data.com/stagea/wgnc34/5413-rb25det/engine/214/ ...but I can prattle on a bit here. These trannies have a thermistor in the sump ~ the TCU reads this and 1. bumps the line pressure up when the ATF is 'cold' and 2. prevents the TC lockup clutch from operating, until the ATF comes up to minimum operating temp (keeps the ATF 'churning' through the TC so it heats up quicker) -- trigger point is around 55C. In these conditions, the engine coolant temperature rises faster than the ATF temperature, and also helps heat the ATF up, which is why it's best to think of the in radiator tank setup as a heat exchanger ; the heat can flow in both directions... ...with these trannies, the 'hot' ATF comes out the front banjo bolt, flows through the cooler/heat exchanger, and returns to the box  via the rear banjo bolt. This gets a mention, due to the wildly different opinions wrt running auto trans fluid coolers ~ do you bypass the in radiator tank altogether, or put the cooler inline with the in radiator tank system...and then, do you put the additional cooler before of after the in radiator tank system?... ....fact is the nominal engine operating temp (roughly 75C), happens to be the ideal temperature for the ATF used in these trannies as well (no surprises there), so for the in radiator tank system to actually 'cool' the ATF, the ATF temp has to be hotter than that...lets say 100C -- you've got 25C of 'excess' heat, (slowly) pumping into the 75C coolant. This part of the equation changes drastically, when you've got 100C ATF flowing through an air cooled radiator ; you can move a lot more excess heat, faster ~ it is possible to cool the ATF 'too much' as it were...(climate matters a lot)... ...in an 'ideal' setup, what you're really trying to control here, is flash heating of the ATF, primarily produced by the TC interface. In a perfect world, wrt auto trans oil cooling, you want a dedicated trans cooler with builtin thermostatic valving - they exist. These should be run inline and before the in radiator tank system ~ when 'cold' the valving bypasses the fin stack, allowing the ATF to flow direct to the in radiator tank heat exchanger, so it works 'as intended' with helping heat the ATF up. When 'hot' (iirc it was 50C threshold), the valving shuts forcing the ATF through the cooler fin stack, and onto the in radiator tank heat exchanger...and you sort of think of it as a 'thermal conditioner' of sorts...ie; if you did cool your ATF down to 65C, the coolant will add a little heat, otherwise it works as intended... ...the 'hot' ATF coming from the front bango bolt, is instantiated from the TC when in use, so all/any flash heated oil, flows to the fluid-to-air cooler first, and because of the greater heat differential, you can get rid of this heat fast. Just how big (BTU/h) this cooler needs to be to effectively dissipate this TC flash heat, is the charm...too many variables to discuss here, but I just wanted to point out the nitty-gritty of automatic trans fluid coolers ~ they're a different beastie to what most ppl think of when considering an 'oil cooler'... /3.5cents   
×
×
  • Create New...