Jump to content
SAU Community

Recommended Posts

My mate has an ARC 'cooler on his M35.

Straight swap for OE.... expensive though :(

There are a few kits available (in order or price) from Greddy (Spec V, Spec R), ARC and Dolphin.

There are probably more, but I cannot think of them off the top of my head.

As far as I know, the Greddy 'coolers need some cutting to fit, but the Dolphin is a slimmer design and fits without cutting (from memory).

As stated the ARC is a straight swap for the stockie.

If you don't want to spend that kind of money, I suppose you could take the dimensions of any of these and duplicate whichever you like.

Can't guarantee the custom job would cool the same though.

Edited by iamhe77

NRVOUS has installed a Greddy V-spec intercooler on his Axis.

http://www.skylinesaustralia.com/forums/in...t&p=4288286

Looks like it fit fine with the fan.

The ARC intercooler does not require any changes to any existing parts to be installed, so the fan is fine with one of these.

You will find more answers on page 7 of that same thread (please read).

I asked NRVOUS how much stuffing around there was when installing the 'cooler, this was his response;

"Like most of these intercooler kits, there's always a little bit of trimming to be done here and there, the reo bar needed some aluminium shaved off at both ends where the intercooler end tanks finish and slots for the stock cooler needed top be cut off so the Greddy clears nicley......now its sits perfectly behind the Bar"

Hope that put's your mind at ease.

Edited by iamhe77
do you have any links or other info on the ARC....or where I can get one from?

Sure mate.

Expensive though :(

Autobarn down here can get one (was quoted ~$2k in Sept last year)

for NM35 Stagea (10/01-7/04)

ARC Part # M103NM35G04

Thickness: 100mm

Purchase price (new) ¥136600

RMS Motorsport (sponsor here) can get it in no probs.

www.fortyone.co.nz can get them in 10 days ($3400NZD though :( )

You can see it cheekily peeping out the opening in my mate's front bar here.

post-31842-1232059701_thumb.jpg

Couldn't add to above post, but here are the dimensions of the Dolphin intercooler

h180mm x w680mm x d70mm

Don't know the part number sorry, bu it is manufactured by Freeway and is supposedly comparable to ARC build/cooling wise

155400 yen new.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
×
×
  • Create New...