Jump to content
SAU Community

Front Torque Gauge

Weapon

By Weapon,
in General Maintenance

 Share

Recommended Posts

Weapon Mentor

Weapon

Posted
Posted

Hey all, just a little confused and looking for a little assistance in regards to the front torque gauge.

I know that the AWD is working however the gauge does not do anything it just sits on 0

I was just wondering if there is an individual fuse for it or anything special like that. I just wanted to see if anyone can direct me rather than just attack it blindly lol

Cheers guys

Link to comment
https://www.sau.com.au/forums/topic/252648-front-torque-gauge/
Share on other sites
GTS4WD Grand Master

GTS4WD

Posted
Posted

Drop the clutch from a standing start.

If the rears just smoke. Its the whole system thats not working.

If bogs down and pulls but the gauge dont move. Its the gauge.

If it bogs down, pulls and gauge begin to dance - She's a goer.

ATTESSA fuses are located in the kick pannel on the right of th steering wheel and in the engine bay drivers side.

Weapon Mentor

Weapon

Posted
  • Author
Posted
Drop the clutch from a standing start.

If the rears just smoke. Its the whole system thats not working.

If bogs down and pulls but the gauge dont move. Its the gauge.

If it bogs down, pulls and gauge begin to dance - She's a goer.

ATTESSA fuses are located in the kick pannel on the right of th steering wheel and in the engine bay drivers side.

Yea i have tested it out and i can tell the AWD is working, went out lastnite to check lol and it was gripping (in the rain) so i might check the fuses as it'd be nice to see that metre working as the other oil temp and boost obviously work fine

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PranK
      eBay "Hella" oil level sensor

      By PranK · Posted

      Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • Kinkstaah
      Jacks that fit under GTR lips that can reach the subframe?

      By Kinkstaah · Posted

      I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • TurboTapin
      Jacks that fit under GTR lips that can reach the subframe?

      By TurboTapin · Posted

      So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • suko
      J50 clock date suddenly reset to January 1

      By suko · Posted

      Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...