Jump to content
SAU Community

Recommended Posts

i just copied this from the supanova site :P

A Novation Agreement– What is it ?.  

A Novation Agreement, when used in conjunction with a vehicle lease represents an agreement between three parties being the employee (lessee), the financier and the employer. The employee leases the vehicle in their own name from the financier, then by attaching the Novation Agreement the following occurs.  

-The employer takes over all the obligations of the lease except for the residual value which remains the obligation of the employee.  

-These obligations remain whilst the employee remains employed. During this period the employer makes all lease payments to the financier from the employee’s salary.  

-If employment is terminated, the Novation Agreement is rescinded (ceased) and only the lease agreement between the employee and the financier remains. When the employee leaves their employment they are required to take the vehicle with them.  

.

Link to comment
https://www.sau.com.au/forums/topic/2529-leases/#findComment-46147
Share on other sites

PeteSmith's is probably a 'conventional' lease, which is paid for with 'after-tax' money, ie take-home pay.

With a novated lease, you effectively pay for the lease with 'before-tax' money, by sacrificing some of your salary for the cost of the lease.

It can be an effective way to reduce PAYE tax, particulary if you are earning in the top tax bracket (> $50k), because it lowers your take-home pay, and the lower take-home pay attracts a lower tax rate.

Link to comment
https://www.sau.com.au/forums/topic/2529-leases/#findComment-46167
Share on other sites

I can highly recommend Leaseplan.

I can highly recommend against Orix.

I am about to find out how good MacMillan-Shakespeare are...

If you work for a large company they may already have an agreement with a preferred fleet company... There are age restrictions on the cars you can lease with the bigger lease/fleet companies though.

Novated Leasing rocks if you set it up correctly, and drive enough km to get the FBT down :D

Any questions, let me know, I'm about to enter my second one :cool:

Link to comment
https://www.sau.com.au/forums/topic/2529-leases/#findComment-47138
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
×
×
  • Create New...