Jump to content
SAU Community

Recommended Posts

yeh pretty much as the title says, having a huge coolant leak from the back of the engine but havent been able to pinpoint where from.

had the car up an put copious amounts of fluid through the radiator and it pisses out the back and from what i can see it gushes out above the gearbox, but there is jus sfa room to have a look where its coming from? ;) any one else similar problem?

i've searched not only this but a few other forums but havent been able to get an answer. jus hoping i could get some sort of an idea before i take it in to a mechanic

cheers for any help

Link to comment
https://www.sau.com.au/forums/topic/253295-r33-s2-leaking-coolant/
Share on other sites

water pump leaking? that tends to be sign of "change me"

hoses to the firewall leaking? ( passenger side)

The drain plug on the engine blow which is on the passenger side leaking?

cant think of much else which could be contributing to a radiator leak at the back of the engine..

Edited by br3ndan
heater hoses

but more than likely the turbo water feed from the back of the plenum.

thats what i was thinking but hoping it wasnt..

thanks for all the help guys will try get some time after work and have a look and take some photos

ok had another look after work today but started to piss down so didnt get much time but its not pump, not the hoses to the firewall im pretty sure its either the heater hoses or the water feed but cant quiet see, pretty sure i've got it pin pointed at the bottom right hand side of the block as u look at it head on.

Taso84 what did you end up having to do with yours?

thanks for any help

this is an absolute broad minded person of a job but you have to do it man

when i did it, it was on my mates s12 w/sr20 conversion and there is NO ROOM at the back

we had to remove the plenum to properly access the hoses

here is a tip: if your struggling undo the gearbox mount and jack the gearbox up higher, it will slope the engine downwards and give you a bit more room to work

here is a pic of the hose i had to replace

post-42017-1232452462_thumb.jpg

sh*t from what i've read this will be aprick of a job or a hit to the back pocket. yeh tell me bout the lack of room its crazy!

yeh i figured i'd be taking some stuff off/out, thanks for the help gfunkk.

jus gunna grab a mate or two and a case an see how we go this weekend i reckon.

cheers for the help fellas

bottom right of an RB - only water above that are heater hoses and the steel turbo feed line.

Or a welsh plug in the block...

go to a mechs and see if they can pressurise your coolant system to allow you to check it exactly.. then see if you want to fix yourself or not

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's plenty of OEM steering arms that are bolted on. Not in the same fashion/orientation as that one, to be sure, but still. Examples of what I'm thinking of would use holes like the ones that have the downward facing studs on the GTR uprights (down the bottom end, under the driveshaft opening, near the lower balljoint) and bolt a steering arm on using only 2 bolts that would be somewhat similarly in shear as these you're complainig about. I reckon old Holdens did that, and I've never seen a broken one of those.
    • Let's be honest, most of the people designing parts like the above, aren't engineers. Sometimes they come from disciplines that gives them more qualitative feel for design than quantitive, however, plenty of them have just picked up a license to Fusion and started making things. And that's the honest part about the majority of these guys making parts like that, they don't have huge R&D teams and heaps of time or experience working out the numbers on it. Shit, most smaller teams that do have real engineers still roll with "yeah, it should be okay, and does the job, let's make them and just see"...   The smaller guys like KiwiCNC, aren't the likes of Bosch etc with proper engineering procedures, and oversights, and sign off. As such, it's why they can produce a product to market a lot quicker, but it always comes back to, question it all.   I'm still not a fan of that bolt on piece. Why not just machine it all in one go? With the right design it's possible. The only reason I can see is if they want different heights/length for the tie rod to bolt to. And if they have the cncs themselves,they can easily offer that exact feature, and just machine it all in one go. 
    • The roof is wrapped
    • This is how I last did this when I had a master cylinder fail and introduce air. Bleed before first stage, go oh shit through first stage, bleed at end of first stage, go oh shit through second stage, bleed at end of second stage, go oh shit through third stage, bleed at end of third stage, go oh shit through fourth stage, bleed at lunch, go oh shit through fifth stage, bleed at end of fifth stage, go oh shit through sixth stage....you get the idea. It did come good in the end. My Topdon scan tool can bleed the HY51 and V37, but it doesn't have a consult connector and I don't have an R34 to check that on. I think finding a tool in an Australian workshop other than Nissan that can bleed an R34 will be like rocking horse poo. No way will a generic ODB tool do it.
    • Hmm. Perhaps not the same engineers. The OE Nissan engineers did not forsee a future with spacers pushing the tie rod force application further away from the steering arm and creating that torque. The failures are happening since the advent of those things, and some 30 years after they designed the uprights. So latent casting deficiencies, 30+ yrs of wear and tear, + unexpected usage could quite easily = unforeseen failure. Meanwhile, the engineers who are designing the billet CNC or fabricated uprights are also designing, for the same parts makers, the correction tie rod ends. And they are designing and building these with motorsport (or, at the very least, the meth addled antics of drifters) in mind. So I would hope (in fact, I would expect) that their design work included the offset of that steering force. Doesn't mean that it is not totally valid to ask the question of them, before committing $$.
×
×
  • Create New...