Jump to content
SAU Community

Recommended Posts

yeh pretty much as the title says, having a huge coolant leak from the back of the engine but havent been able to pinpoint where from.

had the car up an put copious amounts of fluid through the radiator and it pisses out the back and from what i can see it gushes out above the gearbox, but there is jus sfa room to have a look where its coming from? ;) any one else similar problem?

i've searched not only this but a few other forums but havent been able to get an answer. jus hoping i could get some sort of an idea before i take it in to a mechanic

cheers for any help

Link to comment
https://www.sau.com.au/forums/topic/253295-r33-s2-leaking-coolant/
Share on other sites

water pump leaking? that tends to be sign of "change me"

hoses to the firewall leaking? ( passenger side)

The drain plug on the engine blow which is on the passenger side leaking?

cant think of much else which could be contributing to a radiator leak at the back of the engine..

Edited by br3ndan
heater hoses

but more than likely the turbo water feed from the back of the plenum.

thats what i was thinking but hoping it wasnt..

thanks for all the help guys will try get some time after work and have a look and take some photos

ok had another look after work today but started to piss down so didnt get much time but its not pump, not the hoses to the firewall im pretty sure its either the heater hoses or the water feed but cant quiet see, pretty sure i've got it pin pointed at the bottom right hand side of the block as u look at it head on.

Taso84 what did you end up having to do with yours?

thanks for any help

this is an absolute broad minded person of a job but you have to do it man

when i did it, it was on my mates s12 w/sr20 conversion and there is NO ROOM at the back

we had to remove the plenum to properly access the hoses

here is a tip: if your struggling undo the gearbox mount and jack the gearbox up higher, it will slope the engine downwards and give you a bit more room to work

here is a pic of the hose i had to replace

post-42017-1232452462_thumb.jpg

sh*t from what i've read this will be aprick of a job or a hit to the back pocket. yeh tell me bout the lack of room its crazy!

yeh i figured i'd be taking some stuff off/out, thanks for the help gfunkk.

jus gunna grab a mate or two and a case an see how we go this weekend i reckon.

cheers for the help fellas

bottom right of an RB - only water above that are heater hoses and the steel turbo feed line.

Or a welsh plug in the block...

go to a mechs and see if they can pressurise your coolant system to allow you to check it exactly.. then see if you want to fix yourself or not

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...