Jump to content
SAU Community

Recommended Posts

yeh pretty much as the title says, having a huge coolant leak from the back of the engine but havent been able to pinpoint where from.

had the car up an put copious amounts of fluid through the radiator and it pisses out the back and from what i can see it gushes out above the gearbox, but there is jus sfa room to have a look where its coming from? ;) any one else similar problem?

i've searched not only this but a few other forums but havent been able to get an answer. jus hoping i could get some sort of an idea before i take it in to a mechanic

cheers for any help

Link to comment
https://www.sau.com.au/forums/topic/253295-r33-s2-leaking-coolant/
Share on other sites

water pump leaking? that tends to be sign of "change me"

hoses to the firewall leaking? ( passenger side)

The drain plug on the engine blow which is on the passenger side leaking?

cant think of much else which could be contributing to a radiator leak at the back of the engine..

Edited by br3ndan
heater hoses

but more than likely the turbo water feed from the back of the plenum.

thats what i was thinking but hoping it wasnt..

thanks for all the help guys will try get some time after work and have a look and take some photos

ok had another look after work today but started to piss down so didnt get much time but its not pump, not the hoses to the firewall im pretty sure its either the heater hoses or the water feed but cant quiet see, pretty sure i've got it pin pointed at the bottom right hand side of the block as u look at it head on.

Taso84 what did you end up having to do with yours?

thanks for any help

this is an absolute broad minded person of a job but you have to do it man

when i did it, it was on my mates s12 w/sr20 conversion and there is NO ROOM at the back

we had to remove the plenum to properly access the hoses

here is a tip: if your struggling undo the gearbox mount and jack the gearbox up higher, it will slope the engine downwards and give you a bit more room to work

here is a pic of the hose i had to replace

post-42017-1232452462_thumb.jpg

sh*t from what i've read this will be aprick of a job or a hit to the back pocket. yeh tell me bout the lack of room its crazy!

yeh i figured i'd be taking some stuff off/out, thanks for the help gfunkk.

jus gunna grab a mate or two and a case an see how we go this weekend i reckon.

cheers for the help fellas

bottom right of an RB - only water above that are heater hoses and the steel turbo feed line.

Or a welsh plug in the block...

go to a mechs and see if they can pressurise your coolant system to allow you to check it exactly.. then see if you want to fix yourself or not

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
×
×
  • Create New...