Jump to content
SAU Community

Recommended Posts

My screen has a 12v feed and a switched ignition feed.

The little led behind the power button stays on but it hasn't been enough to drain the battery after a week of not being driven.

Samon, I looked into FreeDrive and it kind of implied you had to buy Destinator, so tried to find a distributor in Australia with no luck :P

  • Replies 95
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Samon, I looked into FreeDrive and it kind of implied you had to buy Destinator, so tried to find a distributor in Australia with no luck :P

Try installing MapMonkey first... it includes the Destinator SDK http://www.mapmonkey.net/gps-downloads.html

Then you install FreeDrive (IMHO it's better to use...) and it will find that Destinator is already there and just work...

i wired my car pc and screen a few days ago, when i start the pc up i get "No video signal" on the screen, but i can hear the computer running

connected my home pc to my screen in the car and it was working fine

connected my monitor to the carpc and it still didnt run

any ideas, could it be the video card?

lol it was really simple,, connected it today again, and it was just a matter of flicking through the different video options, it had video 1, video 2, and then Pc

but i think i wired the speakers wrong, caus everytime i turn off the ignition i get a loud noise from the speakers,,,

true i got a bit of a problem ov my own too.. hehe well i went to connect everything all up with my home lcd screen to check if every think is working and no computer i wonder if it has fryed it self im gona pull most of the things out and check it...

but i think i wired the speakers wrong, caus everytime i turn off the ignition i get a loud noise from the speakers,,,

Like a loud 'pop' noise? If so it's just your soundcard isn't gracefully disconnecting when it shuts down :) Not a lot you can do unfortunately except maybe rig up some kinda relay on the amp power trigger wire to switch it off before the soundcard kills the connection...

Like a loud 'pop' noise? If so it's just your soundcard isn't gracefully disconnecting when it shuts down :) Not a lot you can do unfortunately except maybe rig up some kinda relay on the amp power trigger wire to switch it off before the soundcard kills the connection...

i dont think its the sound card, caus the computer doesnt turn off after i take the ignition out, i think its caus i didnt wire the negative to ground, caus the head unit already had another ground wire, im thinking anyway,

i tried installing road runner and all that crap on my home pc,,, but its a fken pain man,,, wish it was easier,,,

i tried installing road runner and all that crap on my home pc,,, but its a fken pain man,,, wish it was easier,,,

Haha yeah it's not the nicest for one-click installation... but it's very customisable. If you just want easy... try Centrafuse or StreetDeck... neither is freeware, but both very good. I went for RR because it was free and because I could tweak it to look and behave exactly how I wanted.

which LCD are you guys using? any problems with it in the car? currently shopping around for the LCD at the moment since I have a laptop lying around.

I'm using a Xenarc 700TSV... works well for me, and now that it's been molded into the dash surround it looks factory as... looks awesome!

I've had no problems with this screen... but the majority of the guys on mp3car.com use either Xenarc or Lilliput (or one of the eBay clones 'SUPER' brand)

how much did you get it for? from mp3car store or local?

Actually I got it on eBay second-hand (apparently the guy had it in his car and it was written off, so he was taking it out as it wasn't gonna be covered by insurance or something) for IIRC just under $200.

Any ideas on how to set up the radio with an in-car pc?

USB FM Tuner...

I tried a few... an ancient D-LINK one, a Griffin RadioShark (AM/FM), and a cheap no-name SiLabs clone... which was the best of the lot! The D-LINK one just plain sucked, the proprietry software that was required for the RadioShark sucked, but the cheapo worked with the SiliconLabs radio software which was used by RoadRunner. I just removed the built-in antenna and soldered on an external socket to hook up to the cars antenna. Works a treat! Only FM mind you, but pfft! Who listens to AM anyway?

Ah very tricky. Im a total n00b at electronis stuff. Looking at the 2din carPC's which seem to involve alot less work

There's a HQCT (High Quality Compact Tuner?) module available from XTroniC (http://direct.xtronic.be/products/hqct-am-fm-usb-radio.html)... it's not cheap but from discussion on mp3car.com the quality of it was comparable to a decent car head unit...

can you take a pic of your lcd in the sun if you don't mind Samon? I want to know how much glare there is on it.

At the moment, sorry but no. The screen isn't in the car. It's not too bad... certainly not as good as a transflective... but I guess you get what you pay for... :laugh:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...